First of all, it is illegal to replace the engine without permission, and the car cannot be examined. If the traffic police find it, the car will be detained, and the insurance will not take effect. Regulations only allow the replacement of the same model of engine. Secondly, many parts of 6T and 0T are not universal, and transplantation is also a big project, which is not much cheaper than buying 328i directly.
The gasoline adsorbed on the carbon after landing will be sucked into the cylinder by the engine and burned, and the mixed gas will thicken. The mixed gas is sometimes thin and sometimes thick, which will cause idle shaking after cold start. The lower the temperature, the greater the amount of oil required for cold start, the more the presence of carbon accumulation will affect the cold start.
cylinder. BMW n13b16The A engine uses a four-cylinder engine. The development history of the BMW four-cylinder engine can be traced back to the engine equipped with the BMW 3/15 model in 1927. The four-cylinder engine is 180 degrees, the six-cylinder engine is 120 degrees, and the engine runs more densely.
Generally, timing marks are marked on the timing gear, front end of the crankshaft and flywheel of the engine. The meaning of the mark is the position of the stop point on the piston of the first cylinder of the engine. With this position, we can easily proofread the timing.
Both models are equipped with the BMW N13B16A 6-liter single-turbo twin-swirl tube supercharged direct injection engine. The maximum power of 116i is 100 kilowatts (136 horsepower) and the maximum torque is 220 Nm; the maximum power of 118i is increased to 125 kilowatts (170 horsepower) and the maximum torque is 250 Nm.
I think the N13B16A is still a great X. After all, it is a 6T high-power version of the supercharged engine released by BMW. The 118I uses this one, which is powerful and fuel-efficient. Secondly, THP160, PSA's newly introduced domestic one, is used in C4L and 3008. The power parameters are also very good, and the speed is rapid, but the fuel consumption is slightly higher.
1. Consider the carbon accumulation in the combustion chamber. Insufficient fuel combustion: When the oil supply of the pump oil is greater than that of the combustion chamber for a long time, the fuel burned by the combustion chamber will form carbon. Before each shutdown, the gear needs to be adjusted to the minimum, so that the fuel supply is relatively small, so that the fuel in the machine can be fully burned. When shut down, the precipitation of carbon accumulation will be reduced.
2. It is difficult for ordinary car owners to distinguish which are faulty and which are reasonable. When I went to the repair shop to test the abnormal sound of the vehicles, only nearly 20% of the vehicles really had problems.
3. Serious carbonization of the engine. The most common reason for engine shaking and idling is excessive carbon accumulation in the fuel injection nozzle. What is carbon accumulation? Carbon accumulation is formed when fuel and air are mixed in the intake system, and some carbon dirt will be attached to sealed areas such as the fuel injector and the top of the piston.
4. There are many reasons for engine shaking: empty air, dirty filter, high-voltage line disconnection, abnormal water temperature, fuel injector blockage, carbon accumulation, grease blockage, etc., which may cause engine shaking. It is recommended that you contact the local 4S store for inspection and maintenance.
1. There are several reasons for the engine shaking of the BMW n13b16a: the engine cylinder is missing: the engine cylinder lack mainly refers to the abnormal operation of one or more cylinders of the engine, generallyIt is manifested as the obvious intermittent flow of exhaust gas discharged by the car. At the same time, the exhaust pipe shakes seriously, and the engine shaking can be clearly felt, sometimes accompanied by a sudden noise.
2. When the vehicle starts, if the engine cold start idle is unstable, it will cause abnormal shaking of the car body. There are many reasons for this situation, including excessive carbon accumulation in the fuel injector, serious carbon accumulation in the engine, serious aging of engine parts, dirty throttle valve, problems with the ignition system, unstable oil pressure of the car, etc.
3. It is difficult for ordinary car owners to distinguish which are faulty and which are reasonable. When I went to the repair shop to test the abnormal sound of the vehicles, only nearly 20% of the vehicles really had problems.
What is the reason for the engine shaking of BMW n13b16a?Trade data for strategic sourcing-APP, download it now, new users will receive a novice gift pack.
First of all, it is illegal to replace the engine without permission, and the car cannot be examined. If the traffic police find it, the car will be detained, and the insurance will not take effect. Regulations only allow the replacement of the same model of engine. Secondly, many parts of 6T and 0T are not universal, and transplantation is also a big project, which is not much cheaper than buying 328i directly.
The gasoline adsorbed on the carbon after landing will be sucked into the cylinder by the engine and burned, and the mixed gas will thicken. The mixed gas is sometimes thin and sometimes thick, which will cause idle shaking after cold start. The lower the temperature, the greater the amount of oil required for cold start, the more the presence of carbon accumulation will affect the cold start.
cylinder. BMW n13b16The A engine uses a four-cylinder engine. The development history of the BMW four-cylinder engine can be traced back to the engine equipped with the BMW 3/15 model in 1927. The four-cylinder engine is 180 degrees, the six-cylinder engine is 120 degrees, and the engine runs more densely.
Generally, timing marks are marked on the timing gear, front end of the crankshaft and flywheel of the engine. The meaning of the mark is the position of the stop point on the piston of the first cylinder of the engine. With this position, we can easily proofread the timing.
Both models are equipped with the BMW N13B16A 6-liter single-turbo twin-swirl tube supercharged direct injection engine. The maximum power of 116i is 100 kilowatts (136 horsepower) and the maximum torque is 220 Nm; the maximum power of 118i is increased to 125 kilowatts (170 horsepower) and the maximum torque is 250 Nm.
I think the N13B16A is still a great X. After all, it is a 6T high-power version of the supercharged engine released by BMW. The 118I uses this one, which is powerful and fuel-efficient. Secondly, THP160, PSA's newly introduced domestic one, is used in C4L and 3008. The power parameters are also very good, and the speed is rapid, but the fuel consumption is slightly higher.
1. Consider the carbon accumulation in the combustion chamber. Insufficient fuel combustion: When the oil supply of the pump oil is greater than that of the combustion chamber for a long time, the fuel burned by the combustion chamber will form carbon. Before each shutdown, the gear needs to be adjusted to the minimum, so that the fuel supply is relatively small, so that the fuel in the machine can be fully burned. When shut down, the precipitation of carbon accumulation will be reduced.
2. It is difficult for ordinary car owners to distinguish which are faulty and which are reasonable. When I went to the repair shop to test the abnormal sound of the vehicles, only nearly 20% of the vehicles really had problems.
3. Serious carbonization of the engine. The most common reason for engine shaking and idling is excessive carbon accumulation in the fuel injection nozzle. What is carbon accumulation? Carbon accumulation is formed when fuel and air are mixed in the intake system, and some carbon dirt will be attached to sealed areas such as the fuel injector and the top of the piston.
4. There are many reasons for engine shaking: empty air, dirty filter, high-voltage line disconnection, abnormal water temperature, fuel injector blockage, carbon accumulation, grease blockage, etc., which may cause engine shaking. It is recommended that you contact the local 4S store for inspection and maintenance.
1. There are several reasons for the engine shaking of the BMW n13b16a: the engine cylinder is missing: the engine cylinder lack mainly refers to the abnormal operation of one or more cylinders of the engine, generallyIt is manifested as the obvious intermittent flow of exhaust gas discharged by the car. At the same time, the exhaust pipe shakes seriously, and the engine shaking can be clearly felt, sometimes accompanied by a sudden noise.
2. When the vehicle starts, if the engine cold start idle is unstable, it will cause abnormal shaking of the car body. There are many reasons for this situation, including excessive carbon accumulation in the fuel injector, serious carbon accumulation in the engine, serious aging of engine parts, dirty throttle valve, problems with the ignition system, unstable oil pressure of the car, etc.
3. It is difficult for ordinary car owners to distinguish which are faulty and which are reasonable. When I went to the repair shop to test the abnormal sound of the vehicles, only nearly 20% of the vehicles really had problems.
What is the reason for the engine shaking of BMW n13b16a?How to reduce shipping delays with data
author: 2024-12-24 00:34Medical diagnostics HS code classification
author: 2024-12-23 23:49Real-time supply chain event updates
author: 2024-12-23 22:55Real-time customs clearance alerts
author: 2024-12-23 22:26HS code metrics for performance dashboards
author: 2024-12-24 00:17Real-time container throughput data
author: 2024-12-23 23:24How to comply with country-specific tariffs
author: 2024-12-23 23:12Canada shipment tracking services
author: 2024-12-23 22:27612.57MB
Check956.34MB
Check361.16MB
Check528.69MB
Check696.11MB
Check277.75MB
Check591.57MB
Check129.95MB
Check435.88MB
Check456.51MB
Check525.95MB
Check529.83MB
Check136.62MB
Check536.36MB
Check496.45MB
Check948.48MB
Check488.77MB
Check898.13MB
Check245.17MB
Check628.37MB
Check221.98MB
Check759.11MB
Check629.16MB
Check952.24MB
Check778.64MB
Check794.97MB
Check514.24MB
Check479.53MB
Check242.16MB
Check765.97MB
Check373.75MB
Check385.87MB
Check869.14MB
Check628.39MB
Check777.56MB
Check145.41MB
CheckScan to install
Trade data for strategic sourcing to discover more
Netizen comments More
1928 Trade data for logistics risk mitigation
2024-12-23 23:57 recommend
1159 HS code-driven risk management frameworks
2024-12-23 23:29 recommend
2979 Textile supply chain HS code mapping
2024-12-23 22:49 recommend
2048 Advanced trade route cost analysis
2024-12-23 22:38 recommend
1724 Crafted wood products HS code references
2024-12-23 22:24 recommend