1. Delay The timing oil control valve of the camshaft controlled by the engine ECU is in the state shown in the figure below. The pressure oil enters the delay working cavity through the camshaft and blade, and the oil pressure pushes the blade and camshaft to rotate in the delayed direction of gas distribution.
2. Check the cylinder gasket, the water-blocking ring of the cylinder liner, the cylinder liner, the cylinder block. If these things are broken, they can cause water to enter the oil bottom. What often happens is the cylinder cushion and the water-blocking ring. Sometimes the engine is short of water and the cylinder head will suddenly explode after adding water and high temperature, and water will also enter the oil bottom. Please check it carefully.
3. Because the water itself has good fluidity and the water circulation speed in the cylinder is relatively fast, once the cylinder pad is damaged, the water in the waterway will flow into the oil channel, causing water to enter the oil span of the water-cooled engine. For normally used dry cylinder liner engines, damage to the cylinder pad is the primary cause of oil inlet, and sometimes the only reason.
1. If the whole car is mainly running at full load in the south, it is recommended to replace a 65° thermoster.
2. Insufficient coolant. Coolant leakage or lack of coolant will cause the engine water temperature to rise. At this time, we should check the coolant situation, ifInsufficient should be added to the appropriate position first, and then check whether the liquid level has dropped seriously in a few days. If so, we need to find the leakage location.
3. Check whether the antifreeze is missing, resulting in high engine water temperature. The circulation of the coolant, whether the circulation is not smooth. Secondly, it can also be checked that water temperature sensors, water pumps, thermosters, cooling fans, etc. can all lead to high water temperature. If your hands-on ability is not very strong, you'd better go to the repair shop for inspection.
4. Confirm whether your water temperature sensor or water temperature gauge is accurate. Can you tell me the specific model of your 6105? If it is a mechanical pump, reduce the injection angle to 2-5 degrees appropriately. If it is a common rail, you need to go to the service station for debugging.
5. After eliminating the radiator problem, it is necessary to check whether the engine thermosator is damaged (cannot be turned on);Check whether the water temperature sensor is falsely reported, whether the water pump belt is too loose, whether the water pump blades are damaged, etc.
It is the damage of the cylinder oil ring, and the spark plug electrode will be wrapped in oil that will not jump. The simple is to open the spark plug to see if Organic oil erosion, and the crankshaft sensor will also cause missing cylinders. Solution: Go to the 4s store to repair the engine.
Hello, if the high-pressure package is a one that controls 4 spark plugs, it is recommended to replace the high-pressure package. I hope it can help you [If there is a problem with the car, ask the car master. 4S store professional technician, 10 minutes to solve.
Analysis problem: this appearsThe problem is usually caused by insufficient rigidity of the body, resulting in deformation of the vehicle while driving, friction or shaking between the door and the frame, or friction between the steel plates due to dewelding in some places.
After a cylinder is "frozen", if the speed of the gasoline engine decreases significantly, it means that the cylinder is working well; if the speed of the gasoline engine decreases very little, it means that the cylinder is not working normally; if the speed of each cylinder basically decreases, it is the same. This shows that each cylinder of the tested gasoline engine has good working uniformity.
1. If it is an engine with SCR, in principle, it is not possible not to add urea. When there is no urea, the alarm will be called, and the engine will be restricted from running.
2. Urea only treats exhaust gas and will not increase fuel consumption. The function of urea solution is to chemically react with nitrogen oxide compounds in the exhaust gas of sand tanks to produce non-toxic nitrogen and water, so as to reduce the emission of toxic gases in the exhaust gas of the car and reduce pollution.
3. Theoretically, it can run, but because there is no urea, the engine will limit the speed. Even if you step on the accelerator, you only have 40 yards in the end. Because the state's inspection of the national four cars is only for the household and the annual review, only to see if there is urea infusion.
4. Jianghuai's Guosi is not bad, isn't it? My new Shuailing is relatively satisfied with the power and fuel consumption. After the first warranty, there is no major problem. Be optimistic. Jianghuai Guosi has both technologies, but it seems that EGR is more. The configuration of the model is different from that of the model. You can go to the 4S store to have a look. Mine doesn't need to add urea.
1. For example: 5W40, 5 is the lowest applicable temperature of engine oil is minus 30 degrees, and W represents winter, indicating that engine oil is universal all year round. 40 is the high-temperature viscosity at 100 degrees.The larger the number, the more viscous the oil will be.
2. Different power: Yuchai 6105 has 135 horsepower, while 6108 has 160 horsepower, so the power values of these two models are different. Yuchai's 6105 is larger than 6108.
3. The engine model is the identification code compiled by the engine manufacturer for a batch of the same products in accordance with relevant regulations, enterprise or industry practices and the attributes of the engine. It is used to represent relevant information such as the manufacturer, specifications, performance, characteristics, processes, uses and product batches of the engine.
4. It is divided into several specifications, which is also the 6105 model. The reason for the different horsepower is that the compression ratio is different, and the position of the upper and lower stop points of the piston is different, which is the so-called high piston and low piston, and the fuel volume of the fuel injector is different.Product performance: YC160-8 is the latest 15-ton excavator launched by Yuchai Heavy Industry.
5. YC is Yuchai engine, CA is the abbreviation of FAW, WP is Weichai, and DL is really unclear.
1. In the diesel generator set R6105IZLD model, R stands for Ricardo, 6 stands for 6 cylinders, 105 stands for cylinder diameter, I stands for stroke, Z stands for supercharging, L stands for medium cooling, and D stands for power generation. Different diesel generator sets have different models, and their numbers and letters represent different meanings.
2. Hello, the code name of Yuchai 6105 engine is YC6J. Baidu search Yuchai official websiteIt can be seen that this model currently has five power segments of 180, 200, 2230 and 245 horsepower to choose from, and the output torque is between 650 and 890 Nm.
3. Different power: Yuchai 6105 has 135 horsepower, while 6108 has 160 horsepower, so the power values of these two models are different. Yuchai's 6105 is larger than 6108.
*Real-time import quota alerts-APP, download it now, new users will receive a novice gift pack.
1. Delay The timing oil control valve of the camshaft controlled by the engine ECU is in the state shown in the figure below. The pressure oil enters the delay working cavity through the camshaft and blade, and the oil pressure pushes the blade and camshaft to rotate in the delayed direction of gas distribution.
2. Check the cylinder gasket, the water-blocking ring of the cylinder liner, the cylinder liner, the cylinder block. If these things are broken, they can cause water to enter the oil bottom. What often happens is the cylinder cushion and the water-blocking ring. Sometimes the engine is short of water and the cylinder head will suddenly explode after adding water and high temperature, and water will also enter the oil bottom. Please check it carefully.
3. Because the water itself has good fluidity and the water circulation speed in the cylinder is relatively fast, once the cylinder pad is damaged, the water in the waterway will flow into the oil channel, causing water to enter the oil span of the water-cooled engine. For normally used dry cylinder liner engines, damage to the cylinder pad is the primary cause of oil inlet, and sometimes the only reason.
1. If the whole car is mainly running at full load in the south, it is recommended to replace a 65° thermoster.
2. Insufficient coolant. Coolant leakage or lack of coolant will cause the engine water temperature to rise. At this time, we should check the coolant situation, ifInsufficient should be added to the appropriate position first, and then check whether the liquid level has dropped seriously in a few days. If so, we need to find the leakage location.
3. Check whether the antifreeze is missing, resulting in high engine water temperature. The circulation of the coolant, whether the circulation is not smooth. Secondly, it can also be checked that water temperature sensors, water pumps, thermosters, cooling fans, etc. can all lead to high water temperature. If your hands-on ability is not very strong, you'd better go to the repair shop for inspection.
4. Confirm whether your water temperature sensor or water temperature gauge is accurate. Can you tell me the specific model of your 6105? If it is a mechanical pump, reduce the injection angle to 2-5 degrees appropriately. If it is a common rail, you need to go to the service station for debugging.
5. After eliminating the radiator problem, it is necessary to check whether the engine thermosator is damaged (cannot be turned on);Check whether the water temperature sensor is falsely reported, whether the water pump belt is too loose, whether the water pump blades are damaged, etc.
It is the damage of the cylinder oil ring, and the spark plug electrode will be wrapped in oil that will not jump. The simple is to open the spark plug to see if Organic oil erosion, and the crankshaft sensor will also cause missing cylinders. Solution: Go to the 4s store to repair the engine.
Hello, if the high-pressure package is a one that controls 4 spark plugs, it is recommended to replace the high-pressure package. I hope it can help you [If there is a problem with the car, ask the car master. 4S store professional technician, 10 minutes to solve.
Analysis problem: this appearsThe problem is usually caused by insufficient rigidity of the body, resulting in deformation of the vehicle while driving, friction or shaking between the door and the frame, or friction between the steel plates due to dewelding in some places.
After a cylinder is "frozen", if the speed of the gasoline engine decreases significantly, it means that the cylinder is working well; if the speed of the gasoline engine decreases very little, it means that the cylinder is not working normally; if the speed of each cylinder basically decreases, it is the same. This shows that each cylinder of the tested gasoline engine has good working uniformity.
1. If it is an engine with SCR, in principle, it is not possible not to add urea. When there is no urea, the alarm will be called, and the engine will be restricted from running.
2. Urea only treats exhaust gas and will not increase fuel consumption. The function of urea solution is to chemically react with nitrogen oxide compounds in the exhaust gas of sand tanks to produce non-toxic nitrogen and water, so as to reduce the emission of toxic gases in the exhaust gas of the car and reduce pollution.
3. Theoretically, it can run, but because there is no urea, the engine will limit the speed. Even if you step on the accelerator, you only have 40 yards in the end. Because the state's inspection of the national four cars is only for the household and the annual review, only to see if there is urea infusion.
4. Jianghuai's Guosi is not bad, isn't it? My new Shuailing is relatively satisfied with the power and fuel consumption. After the first warranty, there is no major problem. Be optimistic. Jianghuai Guosi has both technologies, but it seems that EGR is more. The configuration of the model is different from that of the model. You can go to the 4S store to have a look. Mine doesn't need to add urea.
1. For example: 5W40, 5 is the lowest applicable temperature of engine oil is minus 30 degrees, and W represents winter, indicating that engine oil is universal all year round. 40 is the high-temperature viscosity at 100 degrees.The larger the number, the more viscous the oil will be.
2. Different power: Yuchai 6105 has 135 horsepower, while 6108 has 160 horsepower, so the power values of these two models are different. Yuchai's 6105 is larger than 6108.
3. The engine model is the identification code compiled by the engine manufacturer for a batch of the same products in accordance with relevant regulations, enterprise or industry practices and the attributes of the engine. It is used to represent relevant information such as the manufacturer, specifications, performance, characteristics, processes, uses and product batches of the engine.
4. It is divided into several specifications, which is also the 6105 model. The reason for the different horsepower is that the compression ratio is different, and the position of the upper and lower stop points of the piston is different, which is the so-called high piston and low piston, and the fuel volume of the fuel injector is different.Product performance: YC160-8 is the latest 15-ton excavator launched by Yuchai Heavy Industry.
5. YC is Yuchai engine, CA is the abbreviation of FAW, WP is Weichai, and DL is really unclear.
1. In the diesel generator set R6105IZLD model, R stands for Ricardo, 6 stands for 6 cylinders, 105 stands for cylinder diameter, I stands for stroke, Z stands for supercharging, L stands for medium cooling, and D stands for power generation. Different diesel generator sets have different models, and their numbers and letters represent different meanings.
2. Hello, the code name of Yuchai 6105 engine is YC6J. Baidu search Yuchai official websiteIt can be seen that this model currently has five power segments of 180, 200, 2230 and 245 horsepower to choose from, and the output torque is between 650 and 890 Nm.
3. Different power: Yuchai 6105 has 135 horsepower, while 6108 has 160 horsepower, so the power values of these two models are different. Yuchai's 6105 is larger than 6108.
*Trade data solutions for freight forwarders
author: 2024-12-23 22:59How to detect trade-based money laundering
author: 2024-12-23 22:18International supply chain dashboards
author: 2024-12-23 22:15HS code alignment with import licensing
author: 2024-12-23 21:59Medical implants HS code classification
author: 2024-12-23 20:32High-value machinery HS code classification
author: 2024-12-23 22:16How to reduce transit time variability
author: 2024-12-23 21:22European Union trade analytics
author: 2024-12-23 20:51HS code-based customs broker RFPs
author: 2024-12-23 20:46WTO trade compliance resources
author: 2024-12-23 20:36939.58MB
Check967.52MB
Check747.32MB
Check586.11MB
Check742.98MB
Check226.69MB
Check325.71MB
Check454.83MB
Check747.14MB
Check488.38MB
Check177.24MB
Check272.55MB
Check391.26MB
Check782.82MB
Check718.36MB
Check647.58MB
Check496.83MB
Check187.12MB
Check963.74MB
Check685.63MB
Check272.32MB
Check751.85MB
Check622.79MB
Check454.96MB
Check314.32MB
Check454.12MB
Check851.86MB
Check655.57MB
Check572.53MB
Check821.65MB
Check112.84MB
Check564.54MB
Check287.59MB
Check455.67MB
Check949.98MB
Check734.53MB
CheckScan to install
Real-time import quota alerts to discover more
Netizen comments More
2850 How to analyze competitor shipping routes
2024-12-23 22:18 recommend
1521 Global trade compliance certifications
2024-12-23 22:11 recommend
794 Petroleum products HS code insights
2024-12-23 22:08 recommend
543 Comparative trade performance metrics
2024-12-23 22:03 recommend
1125 How to find ethical suppliers
2024-12-23 20:28 recommend