The function of the piston is to form a combustion chamber with the cylinder head, withstand the gas pressure in the cylinder, and through the piston pin and connecting rod The force is transmitted to the crankshaft. Figure 3-9 shows the cross-section of the piston structure. The piston is mainly composed of four parts: piston top piston skirt piston pin seat 3 and piston ring groove 4.
First of all, the engine housing The shell of the engine plays the role of isolation and sealing from the outside world, absorbing various forces during the operation of the engine.
The engine is composed of two major mechanisms: crank connecting rod mechanism and gas distribution mechanism, as well as five major systems such as cooling, lubrication, ignition, fuel supply and start-up system.The main components include cylinder block, cylinder head, piston, piston pin, connecting rod, crankshaft, flywheel, etc. The inner surface of the cylinder is cylindrical.
1. The mesh distribution of German cars is also the reason why German cars are prone to burning oil. Because the cylinder piston of German cars adopts a mesh distribution, German cars can reduce wear and consumption during driving. Of course, the consequence of this is excessive oil consumption.
2. The main reason for burning engine oil is to use engine oil of poor quality or viscosity level that does not meet the requirements. The low quality level of the oil will lead to increased wear. In addition, the viscosity of the oil is too low.Or too high will cause poor engine lubrication, increase the wear of the piston ring and cylinder wall, reduce the sealing performance, and burn oil.
3. In addition, there are many reasons why German cars burn engine oil. Take Audi Volkswagen, a big oil burner, as an example.
4. The oil storage structure of the German car engine is different. It uses a design similar to a mesh structure. It can make the cylinder wall adsorb more oil, so that the piston ring is easy to form an oil film when moving, so it has a better effect on lubricating oil, but the loss of oil is also greater, so German cars will also burn oil.
The easiest way (for the new car): check whether the exhaust pipe smokes. If there is smoke, it is a two-stroke, and if there is smoke, it is a four-stroke.
The difference between two-stroke and four-stroke engines is simple from the appearance. It can be seen that the heat sink on the cylinder of the two-stroke engine is relatively large, the screws are relatively small, and the cylinder block is obviously longer than the cylinder head. The heat sink on the four-stroke engine cylinder is relatively small, with more screws, and the cylinder block and the cylinder head are almost the same length, and also It's just that the cylinder head is relatively long.
Look at the exhaust gas---The fuel of the two-stroke motorcycle is not burned for the second time. The utilization rate is relatively low, the combustion is insufficient, and its lubricating oil is mixed with gasoline, so the phenomenon of smoke can be seen, especially when driving at high speed.
Steel pipes (HS code ) trade insights-APP, download it now, new users will receive a novice gift pack.
The function of the piston is to form a combustion chamber with the cylinder head, withstand the gas pressure in the cylinder, and through the piston pin and connecting rod The force is transmitted to the crankshaft. Figure 3-9 shows the cross-section of the piston structure. The piston is mainly composed of four parts: piston top piston skirt piston pin seat 3 and piston ring groove 4.
First of all, the engine housing The shell of the engine plays the role of isolation and sealing from the outside world, absorbing various forces during the operation of the engine.
The engine is composed of two major mechanisms: crank connecting rod mechanism and gas distribution mechanism, as well as five major systems such as cooling, lubrication, ignition, fuel supply and start-up system.The main components include cylinder block, cylinder head, piston, piston pin, connecting rod, crankshaft, flywheel, etc. The inner surface of the cylinder is cylindrical.
1. The mesh distribution of German cars is also the reason why German cars are prone to burning oil. Because the cylinder piston of German cars adopts a mesh distribution, German cars can reduce wear and consumption during driving. Of course, the consequence of this is excessive oil consumption.
2. The main reason for burning engine oil is to use engine oil of poor quality or viscosity level that does not meet the requirements. The low quality level of the oil will lead to increased wear. In addition, the viscosity of the oil is too low.Or too high will cause poor engine lubrication, increase the wear of the piston ring and cylinder wall, reduce the sealing performance, and burn oil.
3. In addition, there are many reasons why German cars burn engine oil. Take Audi Volkswagen, a big oil burner, as an example.
4. The oil storage structure of the German car engine is different. It uses a design similar to a mesh structure. It can make the cylinder wall adsorb more oil, so that the piston ring is easy to form an oil film when moving, so it has a better effect on lubricating oil, but the loss of oil is also greater, so German cars will also burn oil.
The easiest way (for the new car): check whether the exhaust pipe smokes. If there is smoke, it is a two-stroke, and if there is smoke, it is a four-stroke.
The difference between two-stroke and four-stroke engines is simple from the appearance. It can be seen that the heat sink on the cylinder of the two-stroke engine is relatively large, the screws are relatively small, and the cylinder block is obviously longer than the cylinder head. The heat sink on the four-stroke engine cylinder is relatively small, with more screws, and the cylinder block and the cylinder head are almost the same length, and also It's just that the cylinder head is relatively long.
Look at the exhaust gas---The fuel of the two-stroke motorcycle is not burned for the second time. The utilization rate is relatively low, the combustion is insufficient, and its lubricating oil is mixed with gasoline, so the phenomenon of smoke can be seen, especially when driving at high speed.
Data-driven supply chain partnerships
author: 2024-12-23 22:51HS code-based customs broker RFPs
author: 2024-12-23 22:36Expert tips on customs data usage
author: 2024-12-23 22:22Carbon steel HS code references
author: 2024-12-23 21:35How to understand INCOTERMS with data
author: 2024-12-23 20:21Optimizing distribution using HS code data
author: 2024-12-23 21:55How to facilitate cross-border returns
author: 2024-12-23 20:52Global trade disruption analysis
author: 2024-12-23 20:48How to simplify export documentation
author: 2024-12-23 20:25Regional value content by HS code
author: 2024-12-23 20:18668.83MB
Check857.61MB
Check633.62MB
Check381.13MB
Check448.19MB
Check847.21MB
Check627.99MB
Check926.75MB
Check382.83MB
Check313.45MB
Check927.59MB
Check339.16MB
Check892.32MB
Check193.32MB
Check781.32MB
Check922.91MB
Check934.83MB
Check959.93MB
Check813.32MB
Check176.19MB
Check795.49MB
Check416.78MB
Check796.84MB
Check721.47MB
Check532.68MB
Check136.31MB
Check615.11MB
Check521.35MB
Check721.65MB
Check813.56MB
Check863.72MB
Check315.34MB
Check537.84MB
Check714.79MB
Check738.42MB
Check649.19MB
CheckScan to install
Steel pipes (HS code ) trade insights to discover more
Netizen comments More
1925 HS code reference for mineral exports
2024-12-23 22:41 recommend
2600 HS code research for EU markets
2024-12-23 21:52 recommend
759 WTO trade compliance resources
2024-12-23 21:35 recommend
1783 Navigating HS code rules in Latin America
2024-12-23 21:10 recommend
1335 Top trade data plugins for analytics
2024-12-23 20:52 recommend