How to validate supplier compliance

List of the contents of this article:

• 1, How to repair the dent of the car bumper?
• 2, How to deal with car scratches
• 3, Can the car dent be repaired?
• 4、The How to validate supplier compliancesurface depression How to solve
• 5, How to repair car pits

How to repair the dent of the car bumper?

Repair method 1: Use hot water. At this stage, most of the front, rear, left and right bumpers of family cars on the market are forged of refined plastic materials. Boiling water can restore the sunken body. The big reason is also very simple. The plastic will become soft when heated, and it can be topped out only by heating up at the concave position.

The way to repair the dent of the car bumper is: use hot water: at present, most of the front and rear bumpers of family cars on the market are made of special plastic materials. Boiling water can restore the dented car body. The reason is also very simple. The plastic will soften when heated, and the concave part can be topped out as long as it is heated. .

Hot water repair, I believe that many car owners know something about the method of hot water to repair the depression of the car body, but this method only has an obvious effect on the repair of the depression of the body bumper, because the bumper is made of plastic and follows the principle of hot expansion and cold contraction.

Hot water repair, many car owners think that warm water is a familiar way to repair body dents, but this method only has an obvious effect on repairing body bumper dents. Because the bumper is made of plastic, it follows the principle of hot expansion and cold contraction.

Use hot water: At present, the front and rear bumpers of family cars on the market are mostly made of special plastic materials. Boiling water can repair the dented car body. The reason is very simple. Plastic will become soft under heat, and the heating can be pushed out in the concave part.

First of all, it is necessary to prepare the tools needed to repair the dent of the car bumper, which are a word change cone and heat the fan heater.

How to deal with car scratching pits

1. There are 3 ways to repair a small pit when a car hits a small pit: if it is a small Pit, you can buy a set of repair tools to repair; go to the repair shop to do traceless repair; you can carry out sheet metal repair. Because it is a small pit, it means that the area is relatively small. You can buy a set of repair tools to repair it.

2. There are five ways to deal with scratches and dents on new cars: traceless repair. This repair method will not damage the paint of the original car. It mainly uses the lever principle to repair on the basis of optics and mechanics. Repair the sheet metal, scrape the putty on the concave part of the car to level it, and then spray paint on the repaired part. Hot water maintenance.

3. The repair method of car bumps is as follows: the first method: heat with hot water and flatten the concave part by yourself. First, boil a large bucket of hot water, and then heat the hot water to the concave place with a spoon. After the plastic is heated to a certain extent, push it out by hand on the back of the concave surface until the concave part protrudes and recovers.

4. Generally speaking, vehicles will encounter a lot of collisions or slight scratches in daily life. If the degree is not heavy, you don't need to go to the repair shop to deal with it, because the cost is high.Car owners can solve problems and reduce expenses by using some tricks.

5. How to deal with car scratches and pits 1 If the car is scratched, if the paint does not fall off, you should go to the repair shop and use the sheet metal method to repair it. If there is paint loss, it needs to be repainted after sheet metal repair.

6. Even if there is a problem, you can ask them to solve it until you are satisfied.

Can the car dent be repaired?

Car dent repair can be solved by pulling and pulling and strong magnetic absorption. First, when the depression is deep and large, you can use the pull-out method, heat the glue gun, apply the melted glue stick to the suction cup, and pull it out. Second, when the depression area is not very large, strong magnetism can be used to suck out the depression with the optical lever dynamic principle.

The main reason is that the depression without paint loss can be repaired as before, the hail pit can be perfectly repaired, and the corners and AB columns are difficult to repair. Automobile dent repair diagram Automobile dent repair technology The repair of dents is based on the principles of optics, physics and mechanics, and uses the lever principle to make dents of different sizes appear on the car body due to various external reasons.

The repair method of car bumps is as follows: the first method: heat with hot water and flatten the concave part by yourself. First, boil a large bucket of hot water, and then heat the hot water to the concave place with a spoon. After the plastic is heated to a certain extent, push it out by hand on the back of the concave surface until the concave part protrudes and recovers.

How to solve the surface depression

Car body depressionThere are three solutions: sheet metal repair. Whether it is a large or a small depression, it can be used to repair. Although sheet metal is expensive to repair, the effect is the best. The owner of the sheet metal project generally cannot complete it by himself, and needs to go to the car repair shop to carry it out.

The repair method of car bumps is as follows: the first method: heat with hot water and flatten the concave part by yourself. First, boil a large bucket of hot water, and then heat the hot water to the concave place with a spoon. After the plastic is heated to a certain extent, push it out by hand on the back of the concave surface until the concave part protrudes and recovers.

Second, the treatment of the machine is to suck out the concave part from the outside with the car dent machine, and then knock it back with a rubber hammer. The part of the tendon can basically be repaired and operated in front of the owner.

How to repair car pits

1. The repair methods of car pits include thermal expansion repair method, 4S store repair, suction cup repair, and rubber stick repair. Thermal expansion repair method: If the place where the bump is made of plastic such as the bumper, it can be heated by splashing boiling water or heating with a hair dryer to suck back the concave place through the characteristics of thermal expansion.

2. The repair methods for the car hitting a small pothole include thermal expansion repair, go to the 4S store to repair, and use a suction cup to repair. Thermal expansion repair method: If the place where the bump is made of plastic such as the bumper, it can be heated by splashing boiling water or heating with a hair dryer to suck back the concave place through the characteristics of thermal expansion.

3. There are two ways to repair car pits, one is sheet metal repair and the other is dent repair.Sheet metal repair is to repair the deformed part of the metal shell of the car.

4. The repair method of the car is as follows: the first method: heat it with hot water and flatten the concave part by yourself. First, boil a large bucket of hot water, and then heat the hot water to the concave place with a spoon. After the plastic is heated to a certain extent, push it out by hand on the back of the concave surface until the concave part protrudes and recovers.