1. Manually on/off automatic start-stop system Suitable for: cars with automatic start-stop system The Supply contracts referencing HS codesbutton (pictured below) is located in the function bar of the display below . Press _ (picture below) to turn on/off. After turning off the function, the color segment on the button will light up.
2. On the automatic transmission car, as long as you release the brake or turn the steering wheel, the engine will immediately ignite automatically, and then you can step on the accelerator and start immediately. The whole process is in D gear. How to turn off the automatic air conditioner of Audi a6? The empty switch of the A6 is the ECON/off button. Short press to turn on or off the economy mode, and long press to completely turn off.
3. When the signal light turns green, the driver can start the "start-stop" engine by stepping on the clutch. The driver hangs the gear and steps on the accelerator to start the vehicle quickly. With the support of high-efficiency battery technology and corresponding engine management procedures, the start-stop system can start normally at low temperatures with a short preheating process.
4. When using the automatic start-stop system, if there is a red light, the engine will be automatically turned off when the vehicle stops. During the shutdown phase, the ignition switch and important auxiliary systems, such as steering assistance and braking assistance, can still be used. When necessary, the engine will automatically start again.
5. The automatic start-stop switch of the Audi A6 is located on the central console, and the specific position is near the screen above the gear lever. The automatic start-stop function of the new Audi A6L cancels the previous mechanical buttons and turns it with a one-button touch switch.When you need to turn off the automatic start-stop function, just touch the corresponding button position.
1. The correct use of automatic start and stop are: step on the brake, wading in the water without starting and stopping, turning on the brake and stepping on the accelerator, etc. Step on the brake. The correct way to start, stop and stop automatically is to step on the brake, stop firmly, then hang the idle gear, and pull the handbrake.
2. The correct way to use automatic start-stop is: when the brake maintenance system is disabled: when the gearshift lever is in D gear, step on the brake pedal and stop the vehicle. ( Engine stop) release the brake pedal and start the engine. When the brake maintenance system is enabled: When the gearshift lever is in D gear, step on the brake pedal and stop the vehicle.
3. The correct steps for automatic start, stop and parking are to step on the brake - stop and then hang the idle gear - pull the handbrake (if there is an electronic handbrake, just press the button directly).
4. Under normal circumstances, when the engine start-stop button is in the ACC state, the steering wheel will be automatically unlocked. If the steering wheel cannot be unlocked normally, you can release the tension by turning the steering wheel left and right and pressing the engine start/stop button at the same time to unlock the steering wheel lock. 2) Turn off/start the engine while driving.
5. The correct use of the automatic start-stop function of the car is as follows: when starting, stop and turning off, quickly turn to P gear, you can release the brake, the engine will not start, continue to stay quietly, when the D gear is turned off, pull up the handbrake and release the brake will not continue to turn off. In order to start faster at any time, even if you hang into the N gear engine It will start.
6. When passing through the waterway section, remember to turn off the start-stop system. In case you need to stop while driving and the engine is turned off, the exhaust pressure will suddenly decrease. Water is easy to flow back into the engine from the exhaust pipe, causing the engine to fail to start.
1. The automatic start-stop function is most suitable for use in open road sections, especially in cities, there are many red lights longer than 100 seconds. When encountering such an intersection, the people present are Idling, if there is a serious traffic jam, an intersection needs 2-3 red lights to pass. In this case, the automatic start-stop function is very useful.
2. First of all, when starting frequently in traffic jamsThe start-stop function is not attractive. After driving for several meters, the brake, the engine will automatically turn off. After a few seconds, the front car will move, and you have to start moving again.
3. Try to control the operation of the start-stop system through the depth of the brake pedal to reduce its negative impact. Then try to turn it off when it passes through the water, and let it run by itself most of the time, which can save some fuel in general.
4. Just release the brake and step on the accelerator or turn the steering wheel gently, and the engine will start again.
5. Jaguar (vs7 one-button start/stop button at the bottom of the central console) is used to start the engine instead of the traditional ignition switch (PressDrive). To start the engine through the start/stop button, the vehicle key must be in the car. Open the pointFire switch, disconnect the brake pedal and clutch pedal without stepping on it, and press the start/stop button to start the vehicle.
The correct method of automatic start-stop is : When the brake maintenance system is disabled: When the gearshift lever is placed in D gear, step on the brake pedal and stop the vehicle.(Engine stop) Loosen the brake pedal and start the engine. When the brake maintenance system is enabled: When the gearshift lever is in D gear, step on the brake pedal and stop the vehicle.
The automatic transmission start-up steps are as follows: ignition. One-click start-up models need to be started with one click twice. The first press is the self-examination of the vehicle, and the second press needs to step on the brake to ignite. Atten your seat belt. Step on the brake. Hang the D gear. Release the handbrake.
Steering wheel lock When the engine start and stop button is closed, the steering wheel is locked to prevent theft; when the door is opened or the smart key is removed from the smart key lock cylinder, the steering wheel will be locked automatically. Under normal circumstances, when the engine start-stop button is in ACC mode, the steering wheel will be automatically unlocked.
Automatic transmission starts and stops automaticallyThe correct usage is as follows: Parking: When you need to stop temporarily, you need to stop the automatic transmission car, hang the gear from D gear to N gear, and then pull up the handbrake to turn off the engine. When parking, you should be careful not to hang in P gear, because it may damage the gearbox.
Automatic transmission car parking steps 1 Step on the brake pedal, make the car slow down slowly, and park in the designated position 2 After the car stops, hang the gear into N gear, and then pull up the handbrake 3 Turn off the car, put the gear in P gear after turning off the engine to prevent the car from slipping. The correct driving method of the automatic transmission car .
1. Generally speaking, press the one-click start button twice first, and then press the brake or clutch button to start the car.Notes on one-click start operation: turn off/start the engine while driving.
2. After the driver sits in the driver's seat, press the button to start. At this time, the ACC light is on, and then press more. At this time, the vehicle will carry out self-inspection. Step on the brake and press the one-button start button to start the ignition. At this time, keep stepping on the brake, hang the D gear, and release the handbrake (just press the electronic handbrake button directly).
3. When stopping, step on the brake, stop the car, pull the D gear to N gear, then pull up the handbrake, continue to step on the footbrake, and start the gear from N. The correct start and stop order with one click. When starting, press the on button first, and then press the on button after the ACC light is on. At this time, the one-click start button becomes green mode. The power supply of the car is connected, and the car is self-checked.
4. Press first when startingPress the on button, and press the on button after the ACC light is on. At this time, the one-button start button is connected to the green mode and the whole car is connected to the power supply. After the car unfolds the self-test and succeeds, then step on the brake, and then press the one-button start button. At this time, the car starts.
1. The correct usage of automatic start and stop are: step on the brake, wading in the water without turning on and stopping, turning on the brake and stepping on the accelerator, etc. Step on the brake. The correct way to start, stop and stop automatically is to step on the brake, stop firmly, then hang the idle gear, and pull the handbrake.
2. The correct way to use automatic start-stop is: when the brake maintenance system is disabled: when the gearshift lever is in D gear, step on the brake pedal and stop the vehicle. ( Engine stop) release the brake pedal and start the engine.When the brake maintenance system is enabled: When the gearshift lever is in D gear, step on the brake pedal and stop the vehicle.
3. Steering wheel lock When the engine start and stop button is closed, the steering wheel is locked to prevent theft; when the door is opened or the smart key is removed from the smart key lock cylinder, the steering wheel will be locked automatically. Under normal circumstances, when the engine start-stop button is in ACC mode, the steering wheel will be automatically unlocked.
Supply contracts referencing HS codes-APP, download it now, new users will receive a novice gift pack.
1. Manually on/off automatic start-stop system Suitable for: cars with automatic start-stop system The Supply contracts referencing HS codesbutton (pictured below) is located in the function bar of the display below . Press _ (picture below) to turn on/off. After turning off the function, the color segment on the button will light up.
2. On the automatic transmission car, as long as you release the brake or turn the steering wheel, the engine will immediately ignite automatically, and then you can step on the accelerator and start immediately. The whole process is in D gear. How to turn off the automatic air conditioner of Audi a6? The empty switch of the A6 is the ECON/off button. Short press to turn on or off the economy mode, and long press to completely turn off.
3. When the signal light turns green, the driver can start the "start-stop" engine by stepping on the clutch. The driver hangs the gear and steps on the accelerator to start the vehicle quickly. With the support of high-efficiency battery technology and corresponding engine management procedures, the start-stop system can start normally at low temperatures with a short preheating process.
4. When using the automatic start-stop system, if there is a red light, the engine will be automatically turned off when the vehicle stops. During the shutdown phase, the ignition switch and important auxiliary systems, such as steering assistance and braking assistance, can still be used. When necessary, the engine will automatically start again.
5. The automatic start-stop switch of the Audi A6 is located on the central console, and the specific position is near the screen above the gear lever. The automatic start-stop function of the new Audi A6L cancels the previous mechanical buttons and turns it with a one-button touch switch.When you need to turn off the automatic start-stop function, just touch the corresponding button position.
1. The correct use of automatic start and stop are: step on the brake, wading in the water without starting and stopping, turning on the brake and stepping on the accelerator, etc. Step on the brake. The correct way to start, stop and stop automatically is to step on the brake, stop firmly, then hang the idle gear, and pull the handbrake.
2. The correct way to use automatic start-stop is: when the brake maintenance system is disabled: when the gearshift lever is in D gear, step on the brake pedal and stop the vehicle. ( Engine stop) release the brake pedal and start the engine. When the brake maintenance system is enabled: When the gearshift lever is in D gear, step on the brake pedal and stop the vehicle.
3. The correct steps for automatic start, stop and parking are to step on the brake - stop and then hang the idle gear - pull the handbrake (if there is an electronic handbrake, just press the button directly).
4. Under normal circumstances, when the engine start-stop button is in the ACC state, the steering wheel will be automatically unlocked. If the steering wheel cannot be unlocked normally, you can release the tension by turning the steering wheel left and right and pressing the engine start/stop button at the same time to unlock the steering wheel lock. 2) Turn off/start the engine while driving.
5. The correct use of the automatic start-stop function of the car is as follows: when starting, stop and turning off, quickly turn to P gear, you can release the brake, the engine will not start, continue to stay quietly, when the D gear is turned off, pull up the handbrake and release the brake will not continue to turn off. In order to start faster at any time, even if you hang into the N gear engine It will start.
6. When passing through the waterway section, remember to turn off the start-stop system. In case you need to stop while driving and the engine is turned off, the exhaust pressure will suddenly decrease. Water is easy to flow back into the engine from the exhaust pipe, causing the engine to fail to start.
1. The automatic start-stop function is most suitable for use in open road sections, especially in cities, there are many red lights longer than 100 seconds. When encountering such an intersection, the people present are Idling, if there is a serious traffic jam, an intersection needs 2-3 red lights to pass. In this case, the automatic start-stop function is very useful.
2. First of all, when starting frequently in traffic jamsThe start-stop function is not attractive. After driving for several meters, the brake, the engine will automatically turn off. After a few seconds, the front car will move, and you have to start moving again.
3. Try to control the operation of the start-stop system through the depth of the brake pedal to reduce its negative impact. Then try to turn it off when it passes through the water, and let it run by itself most of the time, which can save some fuel in general.
4. Just release the brake and step on the accelerator or turn the steering wheel gently, and the engine will start again.
5. Jaguar (vs7 one-button start/stop button at the bottom of the central console) is used to start the engine instead of the traditional ignition switch (PressDrive). To start the engine through the start/stop button, the vehicle key must be in the car. Open the pointFire switch, disconnect the brake pedal and clutch pedal without stepping on it, and press the start/stop button to start the vehicle.
The correct method of automatic start-stop is : When the brake maintenance system is disabled: When the gearshift lever is placed in D gear, step on the brake pedal and stop the vehicle.(Engine stop) Loosen the brake pedal and start the engine. When the brake maintenance system is enabled: When the gearshift lever is in D gear, step on the brake pedal and stop the vehicle.
The automatic transmission start-up steps are as follows: ignition. One-click start-up models need to be started with one click twice. The first press is the self-examination of the vehicle, and the second press needs to step on the brake to ignite. Atten your seat belt. Step on the brake. Hang the D gear. Release the handbrake.
Steering wheel lock When the engine start and stop button is closed, the steering wheel is locked to prevent theft; when the door is opened or the smart key is removed from the smart key lock cylinder, the steering wheel will be locked automatically. Under normal circumstances, when the engine start-stop button is in ACC mode, the steering wheel will be automatically unlocked.
Automatic transmission starts and stops automaticallyThe correct usage is as follows: Parking: When you need to stop temporarily, you need to stop the automatic transmission car, hang the gear from D gear to N gear, and then pull up the handbrake to turn off the engine. When parking, you should be careful not to hang in P gear, because it may damage the gearbox.
Automatic transmission car parking steps 1 Step on the brake pedal, make the car slow down slowly, and park in the designated position 2 After the car stops, hang the gear into N gear, and then pull up the handbrake 3 Turn off the car, put the gear in P gear after turning off the engine to prevent the car from slipping. The correct driving method of the automatic transmission car .
1. Generally speaking, press the one-click start button twice first, and then press the brake or clutch button to start the car.Notes on one-click start operation: turn off/start the engine while driving.
2. After the driver sits in the driver's seat, press the button to start. At this time, the ACC light is on, and then press more. At this time, the vehicle will carry out self-inspection. Step on the brake and press the one-button start button to start the ignition. At this time, keep stepping on the brake, hang the D gear, and release the handbrake (just press the electronic handbrake button directly).
3. When stopping, step on the brake, stop the car, pull the D gear to N gear, then pull up the handbrake, continue to step on the footbrake, and start the gear from N. The correct start and stop order with one click. When starting, press the on button first, and then press the on button after the ACC light is on. At this time, the one-click start button becomes green mode. The power supply of the car is connected, and the car is self-checked.
4. Press first when startingPress the on button, and press the on button after the ACC light is on. At this time, the one-button start button is connected to the green mode and the whole car is connected to the power supply. After the car unfolds the self-test and succeeds, then step on the brake, and then press the one-button start button. At this time, the car starts.
1. The correct usage of automatic start and stop are: step on the brake, wading in the water without turning on and stopping, turning on the brake and stepping on the accelerator, etc. Step on the brake. The correct way to start, stop and stop automatically is to step on the brake, stop firmly, then hang the idle gear, and pull the handbrake.
2. The correct way to use automatic start-stop is: when the brake maintenance system is disabled: when the gearshift lever is in D gear, step on the brake pedal and stop the vehicle. ( Engine stop) release the brake pedal and start the engine.When the brake maintenance system is enabled: When the gearshift lever is in D gear, step on the brake pedal and stop the vehicle.
3. Steering wheel lock When the engine start and stop button is closed, the steering wheel is locked to prevent theft; when the door is opened or the smart key is removed from the smart key lock cylinder, the steering wheel will be locked automatically. Under normal circumstances, when the engine start-stop button is in ACC mode, the steering wheel will be automatically unlocked.
Import export software solutions
author: 2024-12-24 01:18Tire imports HS code classification
author: 2024-12-24 00:47Middle East trade compliance platform
author: 2024-12-23 23:09Insightful trade route analysis
author: 2024-12-23 23:01Beverage industry HS code lookups
author: 2024-12-23 22:54Trade data-driven transport mode selection
author: 2024-12-24 00:45Latin American HS code alignment
author: 2024-12-24 00:44Latin America export data visualization
author: 2024-12-23 23:59Granular HS code detail for compliance officers
author: 2024-12-23 23:44HS code tagging in tariff databases
author: 2024-12-23 23:21
Global trade intelligence for investors
215.86MB
Check
Top trade data APIs for developers
277.49MB
Check
Customs broker performance analysis
862.59MB
Check
HS code-based cost modeling for imports
719.94MB
Check
How to ensure stable supply lines
189.77MB
Check
Sawmill products HS code references
651.66MB
Check
Trade data for route profitability
882.75MB
Check
HS code analytics for port efficiency
645.47MB
Check
Trade data for non-profit organizations
228.22MB
Check
Global tender participation by HS code
283.52MB
Check
Global trade e-commerce insights
827.91MB
Check
How to leverage customs rulings data
795.43MB
Check
Export compliance automation
123.88MB
Check
HS code categorization for finished goods
615.34MB
Check
End-to-end shipment management
243.94MB
Check
Advanced export forecasting models
954.47MB
Check
HS code-based commodity chain analysis
795.56MB
Check
Global trade route simulation
931.62MB
Check
HS code-based global trend analysis
122.66MB
Check
trade data solutions
172.99MB
Check
HS code-based transport cost modeling
293.48MB
Check
global trade management
546.48MB
Check
Rubber exports HS code classification
958.15MB
Check
Global trade compliance best practices
123.88MB
Check
How to use data for HS code classification
582.16MB
Check
How to identify top importing countries
391.54MB
Check
Leveraging global trade statistics
141.53MB
Check
HS code-based textile tariff scheduling
131.96MB
Check
supply chain intelligence
637.65MB
Check
Real-time supplier performance scoring
795.77MB
Check
Low-cost trade data platforms
336.25MB
Check
How to standardize trade documentation
576.53MB
Check
HS code-based cost-cutting strategies
594.73MB
Check
UK trade data management software
671.18MB
Check
How to adapt to shifting trade policies
742.75MB
Check
Trade data integration with ERP systems
722.15MB
Check
Scan to install
Supply contracts referencing HS codes to discover more
Netizen comments More
2249 Textile exports HS code breakdown
2024-12-24 01:13 recommend
681 Global trade customs valuation analysis
2024-12-24 01:06 recommend
560 Global tender participation by HS code
2024-12-24 00:30 recommend
2190 Trade data-driven competitive analysis
2024-12-23 23:16 recommend
1291 shipment tracking services
2024-12-23 22:50 recommend