import export database

List of the table of contents of this article:

• 1、 How to apply car film by yourself?
• 2, The correct method of car filming, the whole process of car filming tutorial< /Li>
• 3, simple and easy Car film tutorial
• 4、car glass film tutorial
• 5,import export database How to paste car glass film

How to apply car film by yourself?

1. Cut the car film and use the film tool to paste the car mold on the car. The specific operation steps are as follows: Before applying the film, first of allMake sure that the working environment meets the requirements of dryness and less dust, otherwise dust and debris will enter during work, which will affect the effect of the film. It is recommended to wash the car before applying the film.

2. The first step: wash the car, clean the inside and outside of the car, and drive the car to a clean and dust-free place to wait for the film to be applied. Step 2: Measure the size of the car window and cut the film according to the size. The size must be appropriate. If you can't grasp it accurately, the size can be slightly larger, but not smaller. Step 3: Clean the window glass.

3. First, buy the car film you need from the Internet. It is much cheaper to paste it by yourself than the 4s store. After buying the car film, cut the car film against the window to be pasted, and the size is slightly larger, as long as the overall shape can be compared.

The correct method of car film The whole process of car film tutorial

Steps of car film: cut the car film according to the size of the car window; wipe and clean the front and rear window glass; use a baking gun to fix the car film; finely cut the car film after the baking film is completed.

Step 1: Wash the car, clean the inside and outside of the car, and drive the car to a clean and dust-free place and wait for the film to be applied. Step 2: Measure the size of the car window and cut the film according to the size. The size must be appropriate. If you can't grasp it accurately, the size can be slightly larger, but not smaller. Step 3: Clean the window glass.

Car film installation steps: car film shaping. The front windshield film with a certain curvature must be fixed before installation, and the cut car film must be covered on the outside of the glass., use a hot air gun to fix the curved part, and stick the car film close to the glass with a scraper while heating.

Car film is applied to car glass to control sunlight and ensure safety. In addition to sunlight control, its basic safety performance includes clarity, anti-glare, ultraviolet insulation, heat insulation, anti-scrature, adhesive glass fragments, sufficient shelf life and privacy protection, ensuring safe driving performance, etc. Increase the beauty.

Test method 1 Test the thermal insulation effect In regular car beauty shops or 4S stores, infrared test lights are generally equipped, so you can ask the merchant for a corner car film to stick to the glass first, put the test light on one side, and put your hand on the other side to feel the thermal insulation effect of the film.

Use special water squeezing tools to eliminate other blisters,Then attach the car film, adjust the position left, right, up and down, and then use the scraper and the baking gun to apply the film. When closing the edge, you can also wrap the cloth with a scraper to close the edge with the low temperature of the baking gun, so as to further give full play to the stickiness of the glue and prevent the bubbles on the edge of the film from rework.

Simple and Easy-to-understand Car Film Tutorial

1. The first step: wash the car, clean the inside and outside of the car, and drive the car to a clean and dust-free place to wait for the film. Step 2: Measure the size of the car window and cut the film according to the size. The size must be appropriate. If you can't grasp it accurately, the size can be slightly larger, but not smaller. Step 3: Clean the window glass.

2. Use a wallpaper knife to tear a bitrarily in any part. Tear the car glass film with your bare hands, use appropriate force, and try not to break the film. Use a knife when you encounter a place that is not easy to tear until it is all finished. Remove glue. There will be a lot of glue left on the glass, which needs to be removed little by little with glue remover, scrapers and rags.

3. Steps to apply film to the car: First, spread two large bath towels on the front cover and instrument, put the chair cover, and wrap it tightly with plastic wrap to prevent accidental sticking and damage when applying the film.Thoroughly clean each piece of glass, mainly take care of the top of the glass, and pay attention to some very small particle impurities.

4. The second step is to cut the film according to the size of the window. Film cutting is an important process for car film pasting. The size of the car cut film is generally determined according to the specific size of the window, which is slightly larger than the size of the window. The third step is to clean the front and rear windows. In addition to cleaning the vehicle, the window glass needs to be carefully cleaned again.

5. Before applying the film to the car, first measure the size of the window and cut the film according to the measured size. Scrub the window glass, completely remove the dirt on the glass, and then clean the water. When pasting the film, tear off the film, spray water evenly on the effective film surface, and then stick it on the car glass to fix it.

6. The film is mainly divided into the following steps: 1 The appearance should be standard, and if it is front and rear blocks, it must be baked well.2 It's better to get a dust-free room. It's better to post it. 3 Wash the glass clean. 4 The paste is to spray some water on the reverse side of the membrane first to prevent the membrane from inhaling small objects. Remember that you can spray some water first.

Automotive Glass Film Tutorial

Automotive Film Tutorial First of all, the car film should be in a clean working environment, preferably dry, less dust or even dust-free. Clean the vehicle in advance and then protect it. Clean each window glass, especially the top and edge of the glass, which is not easy to clean at ordinary times, and then dry the water.

Applying a car film is something that many car owners want to do, but some car owners want to buy a car film by themselves, but they don't know how to stick it. Next, let's take a look at the correct way to apply car film.Before applying the film to the car, first of all, measure the size of the window and cut the film according to the measured size.

Steps for car film: cut the car film according to the size of the car window; wipe and clean the front and rear window glass; use a baking gun to shape the car film; finely cut the car film after the baking film is completed.

Car front windshield film tutorial: First, spread two large bath towels on the front cover and instrument, cover the chair, and wrap it tightly with plastic wrap.

The automotive glass film tutorial is as follows: Before applying the film, first ensure that the working environment meets the requirements of dryness and less dust, otherwise dust and debris will enter during work, which will affect the film effect. It is recommended to wash the car before applying the film.

Car film is a difficult technical work, and the process of filming will also affect the final effect;Some car owners have strong hands-on ability, and the tools are complete, so they will choose to apply the film by themselves.

How to paste car glass film tutorial

Car film tutorial First of all, car film should be in a clean working environment, preferably dry, less dusty or even dust-free. Clean the vehicle in advance and then protect it. Clean each window glass, especially the top and edge of the glass, which is not easy to clean at ordinary times, and then dry the water.

Step 1: Wash the car, clean the inside and outside of the car, and drive the car to a clean and dust-free place and wait for the film to be applied. Step 2: Measure the size of the car window and cut the film according to the size. The size must be appropriate. If you can't grasp it accurately, the size can be slightly larger, but not smaller. Step 3: Clean the window glass.

Use a wallpaper knife to tear a mouth in any part at will. Tear the car glass film with your bare hands, use appropriate force, and try not to break the film. Use a knife when you encounter a place that is not easy to tear until it is all finished. Remove glue. There will be a lot of glue left on the glass, which needs to be removed little by little with glue remover, scrapers and rags.

Car film is a difficult technical work, and the process of filming will also affect the final effect; some car owners have strong hands-on ability and complete tools will choose from their own film.