The function of the piston is to form a combustion chamber with the cylinder head, withstand the gas pressure in the cylinder, and through the piston pin and connecting rod The force is transmitted to the crankshaft. Figure 3-9 shows the cross-section of the piston structure. The piston is mainly composed of four parts: piston top piston skirt piston pin seat 3 and piston ring groove 4.
First of all, the engine housing The shell of the engine plays the role of isolation and sealing from the outside world, absorbing various forces during the operation of the engine.
The engine is composed of two major mechanisms: crank connecting rod mechanism and gas distribution mechanism, as well as five major systems such as cooling, lubrication, ignition, fuel supply and start-up system.The main components include cylinder block, cylinder head, piston, piston pin, connecting rod, crankshaft, flywheel, etc. The inner surface of the cylinder is cylindrical.
1. The mesh distribution of German cars is also the reason why German cars are prone to burning oil. Because the cylinder piston of German cars adopts a mesh distribution, German cars can reduce wear and consumption during driving. Of course, the consequence of this is excessive oil consumption.
2. The main reason for burning engine oil is to use engine oil of poor quality or viscosity level that does not meet the requirements. The low quality level of the oil will lead to increased wear. In addition, the viscosity of the oil is too low.Or too high will cause poor engine lubrication, increase the wear of the piston ring and cylinder wall, reduce the sealing performance, and burn oil.
3. In addition, there are many reasons why German cars burn engine oil. Take Audi Volkswagen, a big oil burner, as an example.
4. The oil storage structure of the German car engine is different. It uses a design similar to a mesh structure. It can make the cylinder wall adsorb more oil, so that the piston ring is easy to form an oil film when moving, so it has a better effect on lubricating oil, but the loss of oil is also greater, so German cars will also burn oil.
The easiest way (for the new car): check whether the exhaust pipe smokes. If there is smoke, it is a two-stroke, and if there is smoke, it is a four-stroke.
The difference between two-stroke and four-stroke engines is simple from the appearance. It can be seen that the heat sink on the cylinder of the two-stroke engine is relatively large, the screws are relatively small, and the cylinder block is obviously longer than the cylinder head. The heat sink on the four-stroke engine cylinder is relatively small, with more screws, and the cylinder block and the cylinder head are almost the same length, and also It's just that the cylinder head is relatively long.
Look at the exhaust gas---The fuel of the two-stroke motorcycle is not burned for the second time. The utilization rate is relatively low, the combustion is insufficient, and its lubricating oil is mixed with gasoline, so the phenomenon of smoke can be seen, especially when driving at high speed.
Africa customs data solutions-APP, download it now, new users will receive a novice gift pack.
The function of the piston is to form a combustion chamber with the cylinder head, withstand the gas pressure in the cylinder, and through the piston pin and connecting rod The force is transmitted to the crankshaft. Figure 3-9 shows the cross-section of the piston structure. The piston is mainly composed of four parts: piston top piston skirt piston pin seat 3 and piston ring groove 4.
First of all, the engine housing The shell of the engine plays the role of isolation and sealing from the outside world, absorbing various forces during the operation of the engine.
The engine is composed of two major mechanisms: crank connecting rod mechanism and gas distribution mechanism, as well as five major systems such as cooling, lubrication, ignition, fuel supply and start-up system.The main components include cylinder block, cylinder head, piston, piston pin, connecting rod, crankshaft, flywheel, etc. The inner surface of the cylinder is cylindrical.
1. The mesh distribution of German cars is also the reason why German cars are prone to burning oil. Because the cylinder piston of German cars adopts a mesh distribution, German cars can reduce wear and consumption during driving. Of course, the consequence of this is excessive oil consumption.
2. The main reason for burning engine oil is to use engine oil of poor quality or viscosity level that does not meet the requirements. The low quality level of the oil will lead to increased wear. In addition, the viscosity of the oil is too low.Or too high will cause poor engine lubrication, increase the wear of the piston ring and cylinder wall, reduce the sealing performance, and burn oil.
3. In addition, there are many reasons why German cars burn engine oil. Take Audi Volkswagen, a big oil burner, as an example.
4. The oil storage structure of the German car engine is different. It uses a design similar to a mesh structure. It can make the cylinder wall adsorb more oil, so that the piston ring is easy to form an oil film when moving, so it has a better effect on lubricating oil, but the loss of oil is also greater, so German cars will also burn oil.
The easiest way (for the new car): check whether the exhaust pipe smokes. If there is smoke, it is a two-stroke, and if there is smoke, it is a four-stroke.
The difference between two-stroke and four-stroke engines is simple from the appearance. It can be seen that the heat sink on the cylinder of the two-stroke engine is relatively large, the screws are relatively small, and the cylinder block is obviously longer than the cylinder head. The heat sink on the four-stroke engine cylinder is relatively small, with more screws, and the cylinder block and the cylinder head are almost the same length, and also It's just that the cylinder head is relatively long.
Look at the exhaust gas---The fuel of the two-stroke motorcycle is not burned for the second time. The utilization rate is relatively low, the combustion is insufficient, and its lubricating oil is mixed with gasoline, so the phenomenon of smoke can be seen, especially when driving at high speed.
Country-specific HS code conversion charts
author: 2024-12-24 01:38Trade data-driven LCL/FCL strategies
author: 2024-12-24 00:53Trade data for industrial raw materials
author: 2024-12-23 23:36How to understand re-export regulations
author: 2024-12-23 23:23Comparing trade data providers
author: 2024-12-24 00:08Organic produce HS code verification
author: 2024-12-23 23:43Trade data-driven supply chain optimization
author: 2024-12-23 23:38HS code-based tariff calculations
author: 2024-12-23 23:28416.71MB
Check185.57MB
Check435.81MB
Check464.28MB
Check948.92MB
Check139.49MB
Check181.53MB
Check858.62MB
Check183.88MB
Check987.35MB
Check511.62MB
Check671.51MB
Check643.86MB
Check659.81MB
Check567.48MB
Check142.66MB
Check432.98MB
Check988.34MB
Check592.51MB
Check324.21MB
Check863.48MB
Check139.16MB
Check583.47MB
Check542.87MB
Check391.45MB
Check189.42MB
Check663.49MB
Check879.82MB
Check257.49MB
Check746.52MB
Check123.91MB
Check818.73MB
Check352.78MB
Check711.15MB
Check525.18MB
Check779.98MB
CheckScan to install
Africa customs data solutions to discover more
Netizen comments More
2176 HS code-based landed cost calculations
2024-12-24 00:59 recommend
1368 Germany international trade insights
2024-12-24 00:06 recommend
2987 On-demand trade data queries
2024-12-24 00:06 recommend
1208 How to reduce import export costs
2024-12-23 23:52 recommend
2633 Data-driven multimodal transport decisions
2024-12-23 23:50 recommend