1. The disassembly method of the rear seat of the car is as follows: the disassembly of the rear seat of the car is divided into the disassembly of the rear seatAnd the disassembly of the rear backrest, the rear seat is only locked, but the rear backrest needs to be disassembled by unscrewing the folding screw. First, open the rear door of the car. Pull up the lock position of the rear seat to remove the rear seat.
2. Generally, the seat cover does not need to be removed from the backrest. After putting the seat down, take out the headrest and install it.
3. [Pacific Automobile Network] The front seat needs to remove the screws of the base. There are four fixing screws in total. First, push the seat to the front, remove the front two screws, and then push the seat to the front and remove the back two screws. The seat was removed. Car seats are basically divided into leather seats and velvet seats.
4. You can put your hand in and touch it at the junction of the base and the backrest. There is a place stuck inside.Press it in a little, lift it up and take it apart. On the other hand, you can disassemble the seat cushion in the same way.
5. Find both sides of the head of the rear seat, pull the wrench, and install it in reverse order of disassembly and installation. Find the wrench on both sides of the head of the rear seat, close to the window, and pull the wrench. The backrest of the rear seat can be turned forward. Lift the rear seat up to remove the cushion, and install it in reverse order of disassembly and installation.
The disassembly method of the rear seat of the car is as follows: the disassembly of the rear seat of the car is divided into the disassembly of the rear seat and the disassembly of the rear backrest. The rear seat is only locked, but the rear seat needs to be unscrewed off the fixing screw of the folding page for disassembly. First, open the rear door of the car. Pull up the lock position of the rear seat to remove the rear seat.
Generally, the seat cover does not need to be removed from the backrest. After putting the seat down, take out the headrest and install it.
Disassembly method: On both sides of the head of the rear seat, near the window, there will be a handle, pull the handle, and the backrest of the rear seat can be turned forward., most of the cushion part of the rear seat is squeezed directly to the rear of the car, and then lifted up to come out.
First of all, in order to have more operating space, the position of the front seat should be moved forward. Then you can open the snap of the fixed seat headrest cover, and take out both the headrest and the headrest cover. Then find the chuck and hook in the gap (between the backrest and the cushion) and take them out of the gap.
Pull the wrench, the backrest of the rear seat can be turned forward, and the rear seat can be lifted up to remove the cushion, which can be installed in the reverse order of disassembly and installation. In order to have more operating space, the position of the front seat should be moved forward. It is best to open the buckle that fixes the seat headrest, and remove both the headrest and headrest.
First, press the button under the rear seat of SAIC General Motors Chevrolet, as shown in the figure below.At this time, you can find the fixing screw on the rear seat of the SAIC GM Chevrolet vehicle, and then remove the fixing screw on the rear seat. Next, you can remove the rear seat cushion of SAIC GM Chevrolet vehicles, see the figure below for details.
The method of disassembly of the car seat cover is as follows: pull open the rubber band behind the backrest headrest and untie the pasted Velcro. Take out the snap that fixes the seat cover from the bottom of the seat, and you can remove the entire seat cover from the bottom to the top.
The disassembly process of the car seat cover is as follows: 1. There will be a sticky buckle on the headrest cover, which can be removed by tearing off the adhesive buckle. Most of the seat covers of the main and co-drivers are fixed with zippers or fasteners, and the fasteners can be removed.
Removing steps for the rear seat cushion of the car (left/middle/right position common): First of all, in order to have more operating space, the position of the front seat should be moved forward. Then you can open the snap of the fixed seat headrest cover, and take out both the headrest and the headrest cover.
Installation and disassembly of the rear seat cushion of the car Remove the headrest of the rear seat, cover the seat backrest on the backrest, fix the top of the seat cover with a hook, and the bottom is stuffed into the gap between the backrest and the cushion through the cushion chuck. Cover the cushion on the rear cushion and fix it again through the cushion cuck into the gap of the backrest such as the cushion.
Car seat leather removal process. There will be a sticky buckle on the head pillowcase. Tear open the adhesive buckle and you can take it off. Most of the seat covers of the main and secondary driving are fixed by zippers or adhesive buckles, which can be taken off by tearing off the adhesive buckles.
The steps for removing the car seat cover are as follows: there will be an adhesive buckle on the headrest cover, and you can tear off the adhesive buckle and take it off. The seat covers of the main and co-drivers are mostly fixed with zippers or adhesive buckles, and they can be taken off by tearing the adhesive buckles.
1. Disassembly method: x0dx0a On both sides of the head of the rear seat, close to the window, there will be a handle, pull the handle, the backrest of the rear seat can be turned forward, the back Most of the cushions of the seats are squeezed directly to the back of the car, and then lifted up to come out.
2. The first thing that needs to be disassembled is the seat cushion, which is usually connected to the base. Use a tool to remove the screw fixing the seat cushion and remove it.Then gently remove the fixing point of the seat cushion and the base with your hand to make it detached.
3. The steps for removing the rear seat of the car are as follows. Find the wrench on both sides of the head of the rear seat, close to the window. Pull the wrench, the backrest of the rear seat can be turned forward, and the rear seat can be lifted up to remove the cushion. Just install it in the reverse order of disassembly and installation.
4. The first step is to find the screws connected and fixed to the rear seat of the car. These screws are in the bottom area of the rear seat of the car and can be removed with a No. 5 wrench or wrench sleeve. Then gently lift the rear seat of the car to remove the barbed wire under the chair. The second step is to remove the headrest of the rear seat of the car.
1. The seat disassembly method of Volkswagen Touareg is as follows: Front seat: There are screws at the end of the slide and slide hard to the end. Rear seat: There is a fixing bolt at the bottom of the seat. If you lift the cover, you can see that the seat can be disassembled by unscrewing the screws and lifting them up hard.
2. Front row: there are screws at the end of the slide, screw it down, slide hard to the end and come down; back row: there are two screws in the calf, screw it down and lift it up hard. As shown in the figure, there is a fixing bolt at the bottom of the seat. You can see the fixing screw when you lift the cover cloth. If you unscrew the screw, you can loosen the seat.
3. The disassembly method of Volkswagen Touareg seats, the seats are fixed with screws. To remove them, the owner needs to remove the screws. The front seat screw is located in front of the track. After removing it, the seat is pushed out. The rear seat screw is located in its calf position. Remove it and then lift the chair hard.
4. There is a pull strap in the middle of the rear seat. Pull the inside of the pull strap up, and the rear seat can be removed. After that, you can take off the rear seat. Take off the left hook on the rear seat.
5. The method of removing the rear seat of Volkswagen Touareg and Wu Baiwan is as follows: Open the trunk, find the lock under the seat, and press the lock. Lift the front of the seat to separate it from the bottom of the seat. Find the foot under the front end of the seat and rotate it in the direction of the arrow on the foot to separate it from the bottom of the seat.
The steps to disassemble the rear seat of the car are as follows. Find the wrench on both sides of the head of the rear seat and close to the window. Pull the wrench, the backrest of the rear seat can be turned forward, and the rear seat can be lifted up to remove the cushion.Just install it in the reverse order of disassembly and installation.
First of all, you need to find the fixing bolts under the seat. These bolts are usually located on both sides of the bottom of the seat, and there may be one or more. Use a wrench or wrench kit to remove these bolts. If the bolts are tight, you can use lubricant or a slight force to loosen them. Next, the seat needs to be put down.
Disassemble the rear seat of Arizer 8 as follows: First, the owner needs to find the latches of the four safety seats on the rear seat of the car, and then gently pick off the lid on the latch.
The rear seat of the vehicle is not tight after being disassembled once, because the buckle of the seat is broken. If the buckle is broken, it needs to be replaced in the repair shop. The replacement price is about 100 yuan. Generally speaking, there will be three seats in the rear seat, and there are four snaps in total. When a snap is broken, the seat will not be too tight.
Disassembly method of the rear seat of the car: on both sides of the head of the rear seat, close to the window, there will be a handle, pull handle, the backrest of the rear seat can be turned forward, and most of the cushion position of the rear seat is directly squeezed to the rear of the car and lift it up.
Pull the wrench, the backrest of the rear seat can be turned forward, and the rear seat can be lifted up to remove the cushion, which can be installed in the reverse order of disassembly and installation. In order to have more operating space, the position of the front seat should be moved forward. It is best to open the buckle that fixes the seat headrest, and remove both the headrest and headrest.
Integrating HS codes in export marketing-APP, download it now, new users will receive a novice gift pack.
1. The disassembly method of the rear seat of the car is as follows: the disassembly of the rear seat of the car is divided into the disassembly of the rear seatAnd the disassembly of the rear backrest, the rear seat is only locked, but the rear backrest needs to be disassembled by unscrewing the folding screw. First, open the rear door of the car. Pull up the lock position of the rear seat to remove the rear seat.
2. Generally, the seat cover does not need to be removed from the backrest. After putting the seat down, take out the headrest and install it.
3. [Pacific Automobile Network] The front seat needs to remove the screws of the base. There are four fixing screws in total. First, push the seat to the front, remove the front two screws, and then push the seat to the front and remove the back two screws. The seat was removed. Car seats are basically divided into leather seats and velvet seats.
4. You can put your hand in and touch it at the junction of the base and the backrest. There is a place stuck inside.Press it in a little, lift it up and take it apart. On the other hand, you can disassemble the seat cushion in the same way.
5. Find both sides of the head of the rear seat, pull the wrench, and install it in reverse order of disassembly and installation. Find the wrench on both sides of the head of the rear seat, close to the window, and pull the wrench. The backrest of the rear seat can be turned forward. Lift the rear seat up to remove the cushion, and install it in reverse order of disassembly and installation.
The disassembly method of the rear seat of the car is as follows: the disassembly of the rear seat of the car is divided into the disassembly of the rear seat and the disassembly of the rear backrest. The rear seat is only locked, but the rear seat needs to be unscrewed off the fixing screw of the folding page for disassembly. First, open the rear door of the car. Pull up the lock position of the rear seat to remove the rear seat.
Generally, the seat cover does not need to be removed from the backrest. After putting the seat down, take out the headrest and install it.
Disassembly method: On both sides of the head of the rear seat, near the window, there will be a handle, pull the handle, and the backrest of the rear seat can be turned forward., most of the cushion part of the rear seat is squeezed directly to the rear of the car, and then lifted up to come out.
First of all, in order to have more operating space, the position of the front seat should be moved forward. Then you can open the snap of the fixed seat headrest cover, and take out both the headrest and the headrest cover. Then find the chuck and hook in the gap (between the backrest and the cushion) and take them out of the gap.
Pull the wrench, the backrest of the rear seat can be turned forward, and the rear seat can be lifted up to remove the cushion, which can be installed in the reverse order of disassembly and installation. In order to have more operating space, the position of the front seat should be moved forward. It is best to open the buckle that fixes the seat headrest, and remove both the headrest and headrest.
First, press the button under the rear seat of SAIC General Motors Chevrolet, as shown in the figure below.At this time, you can find the fixing screw on the rear seat of the SAIC GM Chevrolet vehicle, and then remove the fixing screw on the rear seat. Next, you can remove the rear seat cushion of SAIC GM Chevrolet vehicles, see the figure below for details.
The method of disassembly of the car seat cover is as follows: pull open the rubber band behind the backrest headrest and untie the pasted Velcro. Take out the snap that fixes the seat cover from the bottom of the seat, and you can remove the entire seat cover from the bottom to the top.
The disassembly process of the car seat cover is as follows: 1. There will be a sticky buckle on the headrest cover, which can be removed by tearing off the adhesive buckle. Most of the seat covers of the main and co-drivers are fixed with zippers or fasteners, and the fasteners can be removed.
Removing steps for the rear seat cushion of the car (left/middle/right position common): First of all, in order to have more operating space, the position of the front seat should be moved forward. Then you can open the snap of the fixed seat headrest cover, and take out both the headrest and the headrest cover.
Installation and disassembly of the rear seat cushion of the car Remove the headrest of the rear seat, cover the seat backrest on the backrest, fix the top of the seat cover with a hook, and the bottom is stuffed into the gap between the backrest and the cushion through the cushion chuck. Cover the cushion on the rear cushion and fix it again through the cushion cuck into the gap of the backrest such as the cushion.
Car seat leather removal process. There will be a sticky buckle on the head pillowcase. Tear open the adhesive buckle and you can take it off. Most of the seat covers of the main and secondary driving are fixed by zippers or adhesive buckles, which can be taken off by tearing off the adhesive buckles.
The steps for removing the car seat cover are as follows: there will be an adhesive buckle on the headrest cover, and you can tear off the adhesive buckle and take it off. The seat covers of the main and co-drivers are mostly fixed with zippers or adhesive buckles, and they can be taken off by tearing the adhesive buckles.
1. Disassembly method: x0dx0a On both sides of the head of the rear seat, close to the window, there will be a handle, pull the handle, the backrest of the rear seat can be turned forward, the back Most of the cushions of the seats are squeezed directly to the back of the car, and then lifted up to come out.
2. The first thing that needs to be disassembled is the seat cushion, which is usually connected to the base. Use a tool to remove the screw fixing the seat cushion and remove it.Then gently remove the fixing point of the seat cushion and the base with your hand to make it detached.
3. The steps for removing the rear seat of the car are as follows. Find the wrench on both sides of the head of the rear seat, close to the window. Pull the wrench, the backrest of the rear seat can be turned forward, and the rear seat can be lifted up to remove the cushion. Just install it in the reverse order of disassembly and installation.
4. The first step is to find the screws connected and fixed to the rear seat of the car. These screws are in the bottom area of the rear seat of the car and can be removed with a No. 5 wrench or wrench sleeve. Then gently lift the rear seat of the car to remove the barbed wire under the chair. The second step is to remove the headrest of the rear seat of the car.
1. The seat disassembly method of Volkswagen Touareg is as follows: Front seat: There are screws at the end of the slide and slide hard to the end. Rear seat: There is a fixing bolt at the bottom of the seat. If you lift the cover, you can see that the seat can be disassembled by unscrewing the screws and lifting them up hard.
2. Front row: there are screws at the end of the slide, screw it down, slide hard to the end and come down; back row: there are two screws in the calf, screw it down and lift it up hard. As shown in the figure, there is a fixing bolt at the bottom of the seat. You can see the fixing screw when you lift the cover cloth. If you unscrew the screw, you can loosen the seat.
3. The disassembly method of Volkswagen Touareg seats, the seats are fixed with screws. To remove them, the owner needs to remove the screws. The front seat screw is located in front of the track. After removing it, the seat is pushed out. The rear seat screw is located in its calf position. Remove it and then lift the chair hard.
4. There is a pull strap in the middle of the rear seat. Pull the inside of the pull strap up, and the rear seat can be removed. After that, you can take off the rear seat. Take off the left hook on the rear seat.
5. The method of removing the rear seat of Volkswagen Touareg and Wu Baiwan is as follows: Open the trunk, find the lock under the seat, and press the lock. Lift the front of the seat to separate it from the bottom of the seat. Find the foot under the front end of the seat and rotate it in the direction of the arrow on the foot to separate it from the bottom of the seat.
The steps to disassemble the rear seat of the car are as follows. Find the wrench on both sides of the head of the rear seat and close to the window. Pull the wrench, the backrest of the rear seat can be turned forward, and the rear seat can be lifted up to remove the cushion.Just install it in the reverse order of disassembly and installation.
First of all, you need to find the fixing bolts under the seat. These bolts are usually located on both sides of the bottom of the seat, and there may be one or more. Use a wrench or wrench kit to remove these bolts. If the bolts are tight, you can use lubricant or a slight force to loosen them. Next, the seat needs to be put down.
Disassemble the rear seat of Arizer 8 as follows: First, the owner needs to find the latches of the four safety seats on the rear seat of the car, and then gently pick off the lid on the latch.
The rear seat of the vehicle is not tight after being disassembled once, because the buckle of the seat is broken. If the buckle is broken, it needs to be replaced in the repair shop. The replacement price is about 100 yuan. Generally speaking, there will be three seats in the rear seat, and there are four snaps in total. When a snap is broken, the seat will not be too tight.
Disassembly method of the rear seat of the car: on both sides of the head of the rear seat, close to the window, there will be a handle, pull handle, the backrest of the rear seat can be turned forward, and most of the cushion position of the rear seat is directly squeezed to the rear of the car and lift it up.
Pull the wrench, the backrest of the rear seat can be turned forward, and the rear seat can be lifted up to remove the cushion, which can be installed in the reverse order of disassembly and installation. In order to have more operating space, the position of the front seat should be moved forward. It is best to open the buckle that fixes the seat headrest, and remove both the headrest and headrest.
How to access historical shipment records
author: 2024-12-24 00:43Automated import export risk alerts
author: 2024-12-24 00:33HS code-based freight consolidation
author: 2024-12-24 00:12Agriculture trade data intelligence
author: 2024-12-24 00:10How to analyze customs transaction records
author: 2024-12-23 22:31How to identify export-ready products
author: 2024-12-23 23:37How to leverage data for export growth
author: 2024-12-23 23:35How to find niche import markets
author: 2024-12-23 23:31Sawmill products HS code references
author: 2024-12-23 23:14Customs duty optimization strategies
author: 2024-12-23 22:37
Pharmaceutical trade analytics platform
169.97MB
Check
Global trade content syndication
379.73MB
Check
shipment data access
481.41MB
Check
Crude oil (HS code ) export trends
887.48MB
Check
HS code-based duty drawback claims
868.21MB
Check
How to reduce transit time variability
538.67MB
Check
How to integrate HS codes into BOMs
234.86MB
Check
Special economic zones HS code strategies
439.47MB
Check
Supply chain network modeling
717.22MB
Check
Advanced shipment lead time analysis
965.28MB
Check
HS code-based anti-dumping analysis
645.85MB
Check
Global HS code repository access
169.49MB
Check
Pre-export HS code verification steps
932.44MB
Check
international trade insights
811.59MB
Check
International trade route optimization
969.48MB
Check
Mineral fuels HS code data analysis
775.46MB
Check
Trade flow analysis software
195.18MB
Check
Global trade data accuracy improvement
185.61MB
Check
Industrial spare parts HS code mapping
342.48MB
Check
Global trade partner compliance checks
457.87MB
Check
APAC trade flows by HS code
544.83MB
Check
Comparing trade data providers
436.84MB
Check
Sawmill products HS code references
644.72MB
Check
Global trade agreement analysis
379.49MB
Check
How to capitalize on trade incentives
651.56MB
Check
Renewable energy equipment HS code mapping
168.64MB
Check
Integrating HS codes in export marketing
472.18MB
Check
Trade data-driven logistics planning
612.46MB
Check
Food additives HS code classification
541.79MB
Check
trade data services
265.57MB
Check
Import export software solutions
959.89MB
Check
Identify duty-free items via HS code
292.63MB
Check
Supply chain optimization with trade data
826.79MB
Check
Agricultural machinery HS code lookups
318.53MB
Check
HS code-driven CSR checks
243.77MB
Check
Beverage industry HS code lookups
289.93MB
Check
Scan to install
Integrating HS codes in export marketing to discover more
Netizen comments More
705 Customizable export data queries
2024-12-24 00:50 recommend
991 Agriculture HS code-based quota allocation
2024-12-24 00:36 recommend
2438 International trade knowledge base
2024-12-24 00:07 recommend
2384 Global trade reporting frameworks
2024-12-23 23:42 recommend
1108 HS code alignment with sustainability targets
2024-12-23 22:33 recommend