When installing the camshaft timing gear, it should be in the stop position on the first cylinder, and the timing notation on the flywheel and the flywheel shell is right , and align the engraving line on the timing gear with the engraving line on the gear chamber to hold the gear a little harder, and rotate the camshaft with a screwdriver to insert the positioning pin on the camshaft into the gear positioning pin hole.
, rotate the crankshaft, observe the observation hole on the transmission housing, and align the scale on the flywheel with the fingering on the housing. At this time, the engine cylinder piston is placed in the timing position. Rotate the camshaft, as shown in the figure below, so that the marking of the timing gear on the camshaft is flush with the bottom of the valve chamber cover.
Specific adjustment: (take WD615 as an example): rotate the crankshaft to the "upper stop point" of a cylinder.
The timing gear is marked. Put the mark on the flywheel on it, and the clock is on the cylinder.
There is no time mark in Weichai. The gear of the air pump can be installed directly. Then turn on the timing of the ignition. There is a mark on the oil pump. At the front end of the oil pump. The mark on a thin steel sheet and the mark on the connecting shaft. You will find it if you carefully check the oil pump and turn it around.
Generally, timing marks are marked on the timing gear, front end of the crankshaft and flywheel of the engine. The meaning of the mark is the position of the stop point on the piston of the first cylinder of the engine. With this position, we can easily proofread the timing.
The first step is to check the oil pressure gauge and pressure sensor. The easiest way is to find the same one and replace it. If the fault continues, then proceed to the next step.
Confirm whether the oil pressure switch is normal. If it is normal, it means that the oil pressure is insufficient. Different diesel engines have different oil pressures, which can be found in the manual.I roughly remember that the oil pressure is generally 300-400Kpa. According to your description above, it is very likely that the pressure is insufficient due to the wear of the oil pump.
There are two possibilities, 1 the idle speed is too low, resulting in too low idling pressure. ( Adjust the speed of idle speed) 2 You can adjust the pressure through the pressure regulating valve on the base of the oil core sensor, and it can be solved.
1. There are two ways to adjust the valve order: the first method is according to the engine ignition order (1-5-3-6-2-4) Move the crankshaft, so that the cylinder is in the upper stop position of the working stroke. At this time, the intake and exhaust valves are completely closed, and the valve gap is adjusted. After all the adjustments, the crankshaft needs to be rotated 720 degrees.
2. The first type: cylinder-by-cylinder adjustment method. Use the stacking angle method to judge that the piston is at the upper stop point. Four-cylinder engine (adjust the first cylinder depends on the stacking angle of the fourth cylinder, and then adjust the third cylinder to look at the stacking angle of the second cylinder. Then adjust the fourth cylinder according to the stacking angle of the first cylinder, and finally adjust the second cylinder according to the stacking angle of the third cylinder.
3. The diesel engine should be larger: intake 35~40 wire; exhaust: 45~50 wire.
1. Water has entered the oil pan; 2 The cylinder has been pulled; 3 The plug is broken; 4 The cylinder head is cracked.
2. Because the hot exhaust gas discharged by the engine is caused by air condensation, which is a normal phenomenon. The exhaust pipe at the rear of the vehicle is a main silencer, whose main function is to eliminate the noise of engine exhaust and reduce the pollution of vehicle noise to the environment. Because the main silencer is located at the rear of the car, the temperature is relatively low, and the inside is a multi-cheamber structure, which is easy to form stagnant water.
3、
Global trade pattern recognition-APP, download it now, new users will receive a novice gift pack.
When installing the camshaft timing gear, it should be in the stop position on the first cylinder, and the timing notation on the flywheel and the flywheel shell is right , and align the engraving line on the timing gear with the engraving line on the gear chamber to hold the gear a little harder, and rotate the camshaft with a screwdriver to insert the positioning pin on the camshaft into the gear positioning pin hole.
, rotate the crankshaft, observe the observation hole on the transmission housing, and align the scale on the flywheel with the fingering on the housing. At this time, the engine cylinder piston is placed in the timing position. Rotate the camshaft, as shown in the figure below, so that the marking of the timing gear on the camshaft is flush with the bottom of the valve chamber cover.
Specific adjustment: (take WD615 as an example): rotate the crankshaft to the "upper stop point" of a cylinder.
The timing gear is marked. Put the mark on the flywheel on it, and the clock is on the cylinder.
There is no time mark in Weichai. The gear of the air pump can be installed directly. Then turn on the timing of the ignition. There is a mark on the oil pump. At the front end of the oil pump. The mark on a thin steel sheet and the mark on the connecting shaft. You will find it if you carefully check the oil pump and turn it around.
Generally, timing marks are marked on the timing gear, front end of the crankshaft and flywheel of the engine. The meaning of the mark is the position of the stop point on the piston of the first cylinder of the engine. With this position, we can easily proofread the timing.
The first step is to check the oil pressure gauge and pressure sensor. The easiest way is to find the same one and replace it. If the fault continues, then proceed to the next step.
Confirm whether the oil pressure switch is normal. If it is normal, it means that the oil pressure is insufficient. Different diesel engines have different oil pressures, which can be found in the manual.I roughly remember that the oil pressure is generally 300-400Kpa. According to your description above, it is very likely that the pressure is insufficient due to the wear of the oil pump.
There are two possibilities, 1 the idle speed is too low, resulting in too low idling pressure. ( Adjust the speed of idle speed) 2 You can adjust the pressure through the pressure regulating valve on the base of the oil core sensor, and it can be solved.
1. There are two ways to adjust the valve order: the first method is according to the engine ignition order (1-5-3-6-2-4) Move the crankshaft, so that the cylinder is in the upper stop position of the working stroke. At this time, the intake and exhaust valves are completely closed, and the valve gap is adjusted. After all the adjustments, the crankshaft needs to be rotated 720 degrees.
2. The first type: cylinder-by-cylinder adjustment method. Use the stacking angle method to judge that the piston is at the upper stop point. Four-cylinder engine (adjust the first cylinder depends on the stacking angle of the fourth cylinder, and then adjust the third cylinder to look at the stacking angle of the second cylinder. Then adjust the fourth cylinder according to the stacking angle of the first cylinder, and finally adjust the second cylinder according to the stacking angle of the third cylinder.
3. The diesel engine should be larger: intake 35~40 wire; exhaust: 45~50 wire.
1. Water has entered the oil pan; 2 The cylinder has been pulled; 3 The plug is broken; 4 The cylinder head is cracked.
2. Because the hot exhaust gas discharged by the engine is caused by air condensation, which is a normal phenomenon. The exhaust pipe at the rear of the vehicle is a main silencer, whose main function is to eliminate the noise of engine exhaust and reduce the pollution of vehicle noise to the environment. Because the main silencer is located at the rear of the car, the temperature is relatively low, and the inside is a multi-cheamber structure, which is easy to form stagnant water.
3、
Global trade lead generation tools
author: 2024-12-23 21:32How to detect trade-based money laundering
author: 2024-12-23 21:18How to analyze customs transaction records
author: 2024-12-23 21:15Import data for raw commodities
author: 2024-12-23 20:40HS code-driven risk management frameworks
author: 2024-12-23 22:36HS code alignment with sustainability targets
author: 2024-12-23 21:41Global HS code classification standards
author: 2024-12-23 21:39End-to-end shipment tracking solutions
author: 2024-12-23 20:41Machinery import clearance by HS code
author: 2024-12-23 20:32255.42MB
Check128.82MB
Check468.41MB
Check347.76MB
Check967.49MB
Check345.73MB
Check582.21MB
Check422.15MB
Check928.49MB
Check755.34MB
Check588.79MB
Check897.31MB
Check296.29MB
Check828.43MB
Check948.12MB
Check411.12MB
Check964.36MB
Check156.17MB
Check412.53MB
Check534.52MB
Check164.46MB
Check561.12MB
Check518.11MB
Check719.55MB
Check149.92MB
Check218.13MB
Check567.92MB
Check819.44MB
Check721.58MB
Check149.34MB
Check819.77MB
Check882.95MB
Check957.69MB
Check569.13MB
Check868.77MB
Check236.95MB
CheckScan to install
Global trade pattern recognition to discover more
Netizen comments More
1896 Plastics raw materials HS code lookups
2024-12-23 21:38 recommend
801 Industry-focused HS code reporting
2024-12-23 21:33 recommend
1931 HS code utilization for tariff refunds
2024-12-23 21:11 recommend
2236 Jewelry trade HS code references
2024-12-23 21:10 recommend
709 Predictive trade compliance scoring
2024-12-23 20:24 recommend