There are three main ways to install the baby seat. The traditional installation method is to fix the child seat on the rear seat of the car by the car seat belt.However, in the process of long-term use, people find that the method of fixing seat belts is complicated and there are many cases of misuse.
Put the child seat on the seat, find the lower fixing point, and insert the guide groove under the child safety seat into the lower fixing point in the seat gap until you hear the meshing sound. Raise the headrest to the highest, and then pass the fastening belt through the headrest column, and hook it to the fixing point on the back of the seat, and finally make sure that the fastening belt is not distorted.
Seat belt bundled seat belt bundled installation is to use the seat belt on the car seat to bundle the child safety seat to the car seat. When installing, first place the child safety seat on the car seat, and then tie the seat belt on the car seat to the child safety seat according to the correct path.
There are many installation methods of safety seats, such as ISOFIX fixing method and seat belt fixing method Formula and so on. ISOFIX fixing method: Align, insert and fix the ISOFIX interface of the safety seat with the ISOFIX interface of the vehicle seat.
The method of installing the child safety seat on the seat can refer to the following: seat belt bundled seat belt bundle installation is to use the seat belt on the car seat to bundle the child safety seat to the car seat.
There are 3 common fixing methods for safety seats: seat belt fixing, ISOFIX interface fixing, and LANCH interface fixing. The seat belt is fixed. First, pull out the shoulder strap shaft, open the back of the seat. The seat belt passes through the seat belt guide and fastens the safety buckle. Press the tightening belt to stabilize the system, adjust and tighten the seat belt, and insert it back into the shoulder strap shaft.
The correct installation method of child safety seat is as follows: Material: child safety seat. First of all, check whether there is an ISOFIX interface logo in the rear seat of the car. There are two levers under the child safety seat. Aim the plug-in lever at the ISOFIX latch in the car and insert it.
Correct installation method of child safety seat 1. The correct way to install the child safety seat is to find the lower fixing point (inside the seat gap) and the upper fixing point (behind the headrest/back of the seat) of the rear seat of the car. Then some models have a lid to cover the fixing point, just open it.
Place the child seat on the seat, find the lower fixing point, and insert the guide groove under the child safety seat into the lower fixing point in the seat gap until the mesquench sound is heard. The headrest is raised to the highest, and then the fastening belt passes through the headrest column and hooks it to the fixing point on the back of the seat, and finally make sure that the fastening belt is not twisted.
1. Installation of the front driver's seat cushionMethod: If the front driver's seat cushion of the car has a cap, just put the car seat cushion down, and then there is one or two snaps at the connection of the car seat cushion. You can directly insert the car seat cushion buckle into the seat gap of the seat by hand, so that the car seat cushion will not move forward.
2. First of all, take out the cushion of the new car and check it, as shown in the figure below. Next, put in the cushion vest, as shown in the figure below. Then, put on the seat cushion head cover, as shown in the figure below. Next, take out the cuck, as shown in the figure below. Then, install the chuck on the sling of the seat cushion, as shown in the figure below.
3. First, fasten the child seat on the ISOFIX interface of the car seat, and then tighten the hook according to the tightener, and swing the child seat with your hand to ensure that the seat is completely fixed. XunFind the LATCH interface part, and then stabilize the second hook on the car LATCH interface.
4. The installation of the front seat cushion. First of all, we need to check whether the car cushion we bought is damaged and whether the quality is too high. Adjust the car seat to facilitate seat installation; remove the car headrest; if the front seat cushion has a hat and a hood, just put down the car seat cushion directly.
5. Paragraph 1: How to install car seats is a key task. First of all, make sure that the position and angle of the car seat can ensure the comfort and safety of the driver or passenger. Before starting the installation, you should read the installation manual of the seat carefully to understand the required steps and precautions.
1. Be careful when installing and disassembling. When installing and disassembling, do not pull the Velcro, leather strap, rope, etc. for sewing and installation, so as not to affect the use. After the seat is dirty, gently wipe it with a wet towel (be careful not to use too much force at this time). Parts in the car that have been exposed to direct sunlight for a long time (backrest, etc.) may change color.
2. First, connect the chuck to the elastic band, just pass the elastic band through the chuck. Then insert the slot into the seat gap and pull the chuck out from the back of the seat. Link the elastic band to the metal hook, as shown in the figure below.
3. Take out the car cushion in the front row, put in the cushion vest, cover the cushion head cover, take out the chuck, and install the chuck. Put the cuck into the gap, put it inThe back of the cuck is stuck, the cuck is fastened, the cushion apron is adjusted, the elastic band of the car cushion apron is fastened, and it is put into the car cushion headrest.
1. The car seat cover can be purchased in physical stores or online. If it is dedicated, it can be installed according to the instructions. As long as the seat cover you buy is suitable for your own model, the online store will send tutorials, and you can quickly set it according to the tutorial. When installing, please do not pull the sewn leather straps, ropes, etc.
2. You can install the car seat cover by yourself. If you don't have the ability to do it yourself, you can go to the car beauty salon to install it. Generally, 4S stores do not provide the service of installing seat covers, but you can ask, some 4s stores will also install them.
3. It is not suitable for seats with internal side airbags. Generally, the seat cover of the cloth car should be replaced once every 2 years. Introduction to the attached car seat cover: As the name implies, the car seat cover refers to the cover of the car seat. The car seat cover can protect the original seat from drying and cleaning and prevent the aging of the leather.
4. Take the installation of the Ford Focus seat cushion as an example. First, take out the new car seat cushion and check it, as shown in the figure below. Next, put in the cushion vest, as shown in the figure below. Then, put on the seat cushion head cover, as shown in the figure below. Next, take out the cuck, as shown in the figure below.
5. How to install the car seat cover? To install the headrest, you must first stretch out the headrest of the seat, so that you can see the pre-buried mouth of the original headrest. You must fasten the metal ring on it, and then put on the headcap and adjust the viewing angle, and stick to the bottom elastic band.
6. There is a jam under the rear seat of the front and co-driver to fix the rear cushion. Just pull it out and lift it up! Pay attention to the safety of the card port and return to the original state after installing the seat cover! Step six, put on the seat cover. The installation of the seat cover may be different for the specific car. Please study the instruction manual.
1. The method is very simple. Every car will have a special snap for installing the cushion. This is a belt. There is an elastic band on the back of the car. Put the elastic band into the chuck, insert the chuck into the gap of the car cushion, fix the car cushion, and hang the hook of the car cushion under the seat. On the horizontal bar of the square.
2. Front seat: (1) Car cushion cover purchased backFirst of all, you need to clearly distinguish between the front, back, left and right. You can make a perfect matching alimation by looking at the driver's seat facing inward, or by looking at the airbag hole facing outward.
3. First of all, it should be explained that this article is applicable to the installation of most car cushions, and the special cases of special models are not excluded. Ordinary small cars can be used universally. If you have difficulty in installing, please find a local car beauty shop to install it. The handling fee is generally 20 yuan. If you want to wash your car, a better store may install it for free.
4. The installation of the car cushion cover is as follows: First, move the front seat back for the convenience of installation, and then directly cover the installed front back seat cover down. Then find the chuck inside the seat cover, put it directly into the seat gap, and pull it out from the back of the seat. After pulling it out, smooth the back of the seat cover to make it neat.
5. Some of them do not have a small tongue hook but have a snap with an elastic band. At this time, the snap should pass through the middle gap of the seat through one of the latches and lock it from under the seat to the other latch. In this way, the front driver's seat is installed. The co-driver's seat is also installed in the same way. Installation of rear car cushions.
6. Pass the card through the bottom and fix the long cushion, put the test preparation cover into the cushion, and finally install the long cushion on it, smooth the back seat, and finally complete the work. The above is the trilogy of installing car cushions, but some models may be different, and you should implement them according to different situations.
HS code-based broker fee negotiations-APP, download it now, new users will receive a novice gift pack.
There are three main ways to install the baby seat. The traditional installation method is to fix the child seat on the rear seat of the car by the car seat belt.However, in the process of long-term use, people find that the method of fixing seat belts is complicated and there are many cases of misuse.
Put the child seat on the seat, find the lower fixing point, and insert the guide groove under the child safety seat into the lower fixing point in the seat gap until you hear the meshing sound. Raise the headrest to the highest, and then pass the fastening belt through the headrest column, and hook it to the fixing point on the back of the seat, and finally make sure that the fastening belt is not distorted.
Seat belt bundled seat belt bundled installation is to use the seat belt on the car seat to bundle the child safety seat to the car seat. When installing, first place the child safety seat on the car seat, and then tie the seat belt on the car seat to the child safety seat according to the correct path.
There are many installation methods of safety seats, such as ISOFIX fixing method and seat belt fixing method Formula and so on. ISOFIX fixing method: Align, insert and fix the ISOFIX interface of the safety seat with the ISOFIX interface of the vehicle seat.
The method of installing the child safety seat on the seat can refer to the following: seat belt bundled seat belt bundle installation is to use the seat belt on the car seat to bundle the child safety seat to the car seat.
There are 3 common fixing methods for safety seats: seat belt fixing, ISOFIX interface fixing, and LANCH interface fixing. The seat belt is fixed. First, pull out the shoulder strap shaft, open the back of the seat. The seat belt passes through the seat belt guide and fastens the safety buckle. Press the tightening belt to stabilize the system, adjust and tighten the seat belt, and insert it back into the shoulder strap shaft.
The correct installation method of child safety seat is as follows: Material: child safety seat. First of all, check whether there is an ISOFIX interface logo in the rear seat of the car. There are two levers under the child safety seat. Aim the plug-in lever at the ISOFIX latch in the car and insert it.
Correct installation method of child safety seat 1. The correct way to install the child safety seat is to find the lower fixing point (inside the seat gap) and the upper fixing point (behind the headrest/back of the seat) of the rear seat of the car. Then some models have a lid to cover the fixing point, just open it.
Place the child seat on the seat, find the lower fixing point, and insert the guide groove under the child safety seat into the lower fixing point in the seat gap until the mesquench sound is heard. The headrest is raised to the highest, and then the fastening belt passes through the headrest column and hooks it to the fixing point on the back of the seat, and finally make sure that the fastening belt is not twisted.
1. Installation of the front driver's seat cushionMethod: If the front driver's seat cushion of the car has a cap, just put the car seat cushion down, and then there is one or two snaps at the connection of the car seat cushion. You can directly insert the car seat cushion buckle into the seat gap of the seat by hand, so that the car seat cushion will not move forward.
2. First of all, take out the cushion of the new car and check it, as shown in the figure below. Next, put in the cushion vest, as shown in the figure below. Then, put on the seat cushion head cover, as shown in the figure below. Next, take out the cuck, as shown in the figure below. Then, install the chuck on the sling of the seat cushion, as shown in the figure below.
3. First, fasten the child seat on the ISOFIX interface of the car seat, and then tighten the hook according to the tightener, and swing the child seat with your hand to ensure that the seat is completely fixed. XunFind the LATCH interface part, and then stabilize the second hook on the car LATCH interface.
4. The installation of the front seat cushion. First of all, we need to check whether the car cushion we bought is damaged and whether the quality is too high. Adjust the car seat to facilitate seat installation; remove the car headrest; if the front seat cushion has a hat and a hood, just put down the car seat cushion directly.
5. Paragraph 1: How to install car seats is a key task. First of all, make sure that the position and angle of the car seat can ensure the comfort and safety of the driver or passenger. Before starting the installation, you should read the installation manual of the seat carefully to understand the required steps and precautions.
1. Be careful when installing and disassembling. When installing and disassembling, do not pull the Velcro, leather strap, rope, etc. for sewing and installation, so as not to affect the use. After the seat is dirty, gently wipe it with a wet towel (be careful not to use too much force at this time). Parts in the car that have been exposed to direct sunlight for a long time (backrest, etc.) may change color.
2. First, connect the chuck to the elastic band, just pass the elastic band through the chuck. Then insert the slot into the seat gap and pull the chuck out from the back of the seat. Link the elastic band to the metal hook, as shown in the figure below.
3. Take out the car cushion in the front row, put in the cushion vest, cover the cushion head cover, take out the chuck, and install the chuck. Put the cuck into the gap, put it inThe back of the cuck is stuck, the cuck is fastened, the cushion apron is adjusted, the elastic band of the car cushion apron is fastened, and it is put into the car cushion headrest.
1. The car seat cover can be purchased in physical stores or online. If it is dedicated, it can be installed according to the instructions. As long as the seat cover you buy is suitable for your own model, the online store will send tutorials, and you can quickly set it according to the tutorial. When installing, please do not pull the sewn leather straps, ropes, etc.
2. You can install the car seat cover by yourself. If you don't have the ability to do it yourself, you can go to the car beauty salon to install it. Generally, 4S stores do not provide the service of installing seat covers, but you can ask, some 4s stores will also install them.
3. It is not suitable for seats with internal side airbags. Generally, the seat cover of the cloth car should be replaced once every 2 years. Introduction to the attached car seat cover: As the name implies, the car seat cover refers to the cover of the car seat. The car seat cover can protect the original seat from drying and cleaning and prevent the aging of the leather.
4. Take the installation of the Ford Focus seat cushion as an example. First, take out the new car seat cushion and check it, as shown in the figure below. Next, put in the cushion vest, as shown in the figure below. Then, put on the seat cushion head cover, as shown in the figure below. Next, take out the cuck, as shown in the figure below.
5. How to install the car seat cover? To install the headrest, you must first stretch out the headrest of the seat, so that you can see the pre-buried mouth of the original headrest. You must fasten the metal ring on it, and then put on the headcap and adjust the viewing angle, and stick to the bottom elastic band.
6. There is a jam under the rear seat of the front and co-driver to fix the rear cushion. Just pull it out and lift it up! Pay attention to the safety of the card port and return to the original state after installing the seat cover! Step six, put on the seat cover. The installation of the seat cover may be different for the specific car. Please study the instruction manual.
1. The method is very simple. Every car will have a special snap for installing the cushion. This is a belt. There is an elastic band on the back of the car. Put the elastic band into the chuck, insert the chuck into the gap of the car cushion, fix the car cushion, and hang the hook of the car cushion under the seat. On the horizontal bar of the square.
2. Front seat: (1) Car cushion cover purchased backFirst of all, you need to clearly distinguish between the front, back, left and right. You can make a perfect matching alimation by looking at the driver's seat facing inward, or by looking at the airbag hole facing outward.
3. First of all, it should be explained that this article is applicable to the installation of most car cushions, and the special cases of special models are not excluded. Ordinary small cars can be used universally. If you have difficulty in installing, please find a local car beauty shop to install it. The handling fee is generally 20 yuan. If you want to wash your car, a better store may install it for free.
4. The installation of the car cushion cover is as follows: First, move the front seat back for the convenience of installation, and then directly cover the installed front back seat cover down. Then find the chuck inside the seat cover, put it directly into the seat gap, and pull it out from the back of the seat. After pulling it out, smooth the back of the seat cover to make it neat.
5. Some of them do not have a small tongue hook but have a snap with an elastic band. At this time, the snap should pass through the middle gap of the seat through one of the latches and lock it from under the seat to the other latch. In this way, the front driver's seat is installed. The co-driver's seat is also installed in the same way. Installation of rear car cushions.
6. Pass the card through the bottom and fix the long cushion, put the test preparation cover into the cushion, and finally install the long cushion on it, smooth the back seat, and finally complete the work. The above is the trilogy of installing car cushions, but some models may be different, and you should implement them according to different situations.
Logistics optimization by HS code
author: 2024-12-23 21:21HS code-based compliance cost reduction
author: 2024-12-23 22:00Metal scrap HS code classification
author: 2024-12-23 21:54Sourcing opportunities filtered by HS code
author: 2024-12-23 21:53Renewable energy equipment HS code mapping
author: 2024-12-23 21:39Trade intelligence for marine cargo
author: 2024-12-23 21:35736.47MB
Check698.54MB
Check761.54MB
Check122.83MB
Check833.49MB
Check316.14MB
Check738.23MB
Check371.96MB
Check926.23MB
Check446.79MB
Check273.88MB
Check474.29MB
Check684.88MB
Check331.35MB
Check417.12MB
Check386.85MB
Check173.96MB
Check522.18MB
Check999.35MB
Check549.83MB
Check942.27MB
Check271.68MB
Check721.14MB
Check714.37MB
Check459.65MB
Check485.46MB
Check333.59MB
Check427.56MB
Check921.46MB
Check333.11MB
Check443.33MB
Check781.35MB
Check214.46MB
Check535.56MB
Check756.32MB
Check696.45MB
CheckScan to install
HS code-based broker fee negotiations to discover more
Netizen comments More
1213 Real-time embargo monitoring
2024-12-23 22:30 recommend
2500 UK trade data management software
2024-12-23 22:22 recommend
2407 Processed nuts HS code references
2024-12-23 21:35 recommend
842 HS code compliance for Nordic countries
2024-12-23 21:18 recommend
2144 How to standardize trade documentation
2024-12-23 20:58 recommend